| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Double sides effect http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10101&t=16415 |
Page 1 of 1 |
| Author: | Laurent Brondel [ Sat Mar 15, 2008 5:40 pm ] |
| Post subject: | Double sides effect |
It's a question aimed at those who switched to laminating their sides (or using tall solid linings). I assume the added thickness, and/or mass, will raise the pitch of the rim. Am I right to assume that this in turn will raise the pitch of the soundbox? |
|
| Author: | Burton LeGeyt [ Sat Mar 15, 2008 6:40 pm ] |
| Post subject: | Re: Double sides effect |
Laurent, I have been using 2 laminations at .04 with the lightest mahogany I can find as the inner layer. I don't think they are heavier than a single side of a dense rosewood. If they are, it is a very small bit. As for raising the pitch of the box, I didn't think the sides played a part in this assuming they are relatively stiff. If I am wrong here I would love to know. As an aside, I would think the stiffness would affect the pitch more as it affected the loss of energy in the top and back and I don't find double sides much stiffer than a single of the same thickness carefully bent. Maybe a little, but not much. The solid linings do make a huge difference though in that regard. |
|
| Author: | Laurent Brondel [ Sun Mar 16, 2008 2:31 pm ] |
| Post subject: | Re: Double sides effect |
Burton, I think others who laminate their sides arrive at around .100" thickness, perhaps more. From what Howard and others say, the rim is extra-stiff and doesn't even need the mold at that point. I'm just assuming the rim rings higher. Thus the soundbox when closed, maybe I am wrong, but it would seem logical. I'm wondering if you guys compensate for that in tuning the plates, opening a soundport etc. |
|
| Author: | Rick Turner [ Sun Mar 16, 2008 2:50 pm ] |
| Post subject: | Re: Double sides effect |
I'm now using a solid tall lining inside a conventional thickness side set (about .085") for a total of around .170". Then I use reverse kerfing inside that...and top that off with a layer of carbon fiber...and then use three layers of .021" CF as binding on some guitars. These suckers are stiff... I don't think the pitch of the sides has much to do with the tonal results which I think has more to do with how I graduate and brace the top. My back pitch is pretty high as that's got CF topped braces. With this series of guitars, I'm going for a lot of forward directional output and very solid mids without the muddy low end that can be captivating but ultimately not musically rewarding. |
|
| Author: | Ken McKay [ Sun Mar 16, 2008 3:02 pm ] |
| Post subject: | Re: Double sides effect |
I have never thought of sides in terms of their pitch but rather their stiffness or floppiness. I think with stiff sides you will get a lot of "ping" or what Rick calls forward movement. My opinion is that you gain this "ping" at the expense of some "warmth" - as in banjo like, or maybe piano like. |
|
| Author: | Laurent Brondel [ Sun Mar 16, 2008 4:39 pm ] |
| Post subject: | Re: Double sides effect |
Rick, I definitely notice an improvement in clarity and projection with a stiffer back and I tend to like it. Stiff sides probably contribute some more toward that goal, no doubt. Beyond structural integrity. But I suspect the sides play a role, maybe very slight, in how the soundbox vibrates. Hence my query about the rim's pitch, or resonance, or whatever. Ken, I agree: some of the "openness" (for lack of a better term…) of some vintage guitars may be because of extremely thin sides. Perhaps it transpires some sound toward the player, and/or absorbs energy, I am not sure. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|