Official Luthiers Forum!
http://w-ww.luthiersforum.com/forum/

Microplane
http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10101&t=16567		 Page 1 of 1
Author:  CraigL [ Tue Mar 25, 2008 9:26 am ]
Post subject:  Microplane
The other day I purchased some of the discs made by Microplane for random orbital sanders, and finally had the opportunity to use them last night as I was working on some cedar and Engelmann soundboards. I was very impressed and pleased with their performance. I have also used one of their rasp-like devices when shaping the mahogany heel of my last guitar. That also worked extremely well. They seem to have good products at a reasonable price, and I think they are a good option for a luthier's armamentarium. [:Y:]
Author:  Mitch Cain [ Tue Mar 25, 2008 9:38 am ]
Post subject:  Re: Microplane
those Microplane rasps are also very handy in the kitchen as cheese and veggie graters! :shock:
Author:  WaddyThomson [ Tue Mar 25, 2008 9:54 am ]
Post subject:  Re: Microplane
I have one of the little Microplane Drums for a drill press. It can also be used in a hand drill, though an electric one works best because it has a higher speed. They are great. There is both a 1" drum and a 2 1/2" one. They also have a flush cut attachment that lets you follow a mold, like with a trim bit on a router.
Author:  Glenn LaSalle [ Tue Mar 25, 2008 11:05 am ]
Post subject:  Re: Microplane
Hi Craig,

Did you buy it on-line? If you did, is there a link?

Thx!

Glenn
Author:  ecklesweb [ Tue Mar 25, 2008 12:08 pm ]
Post subject:  Re: Microplane
Interesting...I bought a set of the three different "grits" and was so disappointed in them that I took them back to the store for a refund. idunno

Glad you found them useful. They're certainly not too expensive to try out in any case.
Author:  charliewood [ Tue Mar 25, 2008 2:24 pm ]
Post subject:  Re: Microplane
Another great thing about them is that they make chips and not dust!
I have a couple round bottom hand rasps - but Im anxious to get the drill press style one!
Cheers
Charlie
Author:  Marc Lupien [ Tue Mar 25, 2008 2:48 pm ]
Post subject:  Re: Microplane
I've got the drill press set with the pattern follower. I used it only once since it tended to pack the chips inside and I had to clean it every couple of minutes... This is a light duty tool.

My 0.02$ (canadian) :D

Marc
Author:  Bruce Dickey [ Tue Mar 25, 2008 6:35 pm ]
Post subject:  Re: Microplane
I've got a couple.

Even though made in my hometown, I purchased mine from Lee Valley in Ohio? I think that's right.

I use them for necks.

Others have commented that theirs seemed to dull after a bit. After all, they are more edge tools like a razor for your face. So, if you buy them think of them as expendable.

While I still have both of mine, I remember using mainly files on my last neck.
Author:  rjcguitar [ Wed Mar 26, 2008 9:09 am ]
Post subject:  Re: Microplane
glasalle wrote:
Hi Craig,

Did you buy it on-line? If you did, is there a link?

Thx!

Glenn



http://us.microplane.com/index.asp?Page ... ategory=23
Author:  CraigL [ Wed Mar 26, 2008 1:19 pm ]
Post subject:  Re: Microplane
I got them at Rockler, in the store. Since my first post, I have tried them on various woods, and there is a difference in their effectiveness. Softwoods worked well, as did Mahogany. Granadillo has been more of a chore, but I guess Granadillo has a bit of a rep for being more tenacious anyway.
Author:  Barry Daniels [ Wed Mar 26, 2008 2:18 pm ]
Post subject:  Re: Microplane
I made a run of 36 archtop necks using both hard birdseye maple, and soft curly maple. I tried a lot of different tools and the Microplane half round blade in a hacksaw frame came out the winner. Fastest hand carving tool around, and they leave a relatively smooth surface. The half round works great on the heel and headstock transition. I have only been able to find this particular style of Microplane blade at Japan Woodworker. In fact, I don't even see this blade on the Microplane website!
Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/