Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Nov 28, 2024 4:30 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Sat Dec 07, 2019 10:31 am 
Offline
Koa
Koa
User avatar

Joined: Sat Jan 19, 2013 7:33 am
Posts: 1876
First name: Willard
Last Name: Guthrie
City: Cumberland
State: Maryland 21502
Zip/Postal Code: 21502
Country: United State
Focus: Repair
Status: Semi-pro
Recovering from a particularly viscous head cold, so taking a bit of a break from work to solicit some opinions on proper bar fret height after a refret or adjustment. It seems like there are at least three schools of thought on this:

1. 0.045-0.050 in. - pretty much the TJ Thompson approach...lots of height to handle a couple L/C/P before another refret or 'lifting' of the wire. Also where the boss prefers the height.

2. 0.037 in. - what Martin's bar fret maestro mills his to on new or refret work...apparently very adept at using a pneumatic body work file to rough the height before final level and crowning!!! Wish I had been on that particular trip.

3. 0.025-0.030 in - what at least a few online seem to prefer, although it's hard to tell if these individuals are truly doing bar fret work or simply talking about it.

Opinions? Rationale?

_________________
For the times they are a changin'

- Bob Dylan


Top
 Profile  
 
PostPosted: Sat Dec 07, 2019 11:28 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat May 22, 2010 10:32 am
Posts: 2616
First name: alan
Last Name: stassforth
City: Santa Rosa
State: ca
Zip/Postal Code: 95404
Country: usa
Focus: Build
Status: Amateur
What's "bar fret height" ?
Also, what's "L/C/P" ?
Alan


Top
 Profile  
 
PostPosted: Sat Dec 07, 2019 11:35 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5825
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Quote:
Also, what's "L/C/P" ?


Level, crown, polish.

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Sat Dec 07, 2019 12:46 pm 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 13388
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
We are in the .045" camp for the reasons that you cited, serviceability for L,C,P's in the future. It's also what most folks are used to these days, higher frets.

I don't know what's historically accurate though and come to think of it I don't recall ever measuring untouched bar fret height when we encounter them. It's pretty rare for us these days to see bar frets or agree to work on them since we are now shying away from big arse jobs.

Speculation on my part but your (2) may be what it is for historical accuracy at least for Martin's with bar frets. Again speculation on my part.

Lastly taking down excess height with files is a tough slog. We spent nearly a day and a half just knocking off .010" on my Strat.... Will never do that again and the next time we had a calling to reduce fret height we refretted it in half the time.

Hope you feel better.



These users thanked the author Hesh for the post: Clinchriver (Sat Dec 07, 2019 1:44 pm)
Top
 Profile  
 
PostPosted: Sat Dec 07, 2019 7:46 pm 
Offline
Koa
Koa
User avatar

Joined: Sat Jan 19, 2013 7:33 am
Posts: 1876
First name: Willard
Last Name: Guthrie
City: Cumberland
State: Maryland 21502
Zip/Postal Code: 21502
Country: United State
Focus: Repair
Status: Semi-pro
I apologize for authoring such a cryptic post, Mr. Stassforth - I'll blame the massive doses of DayQuil!.

Bar frets are the type of fret used by Martin up through 1933 (well past the time when every other company had moved to standard T frets), so repair shops sometimes see these guitars in for work, to include fret leveling, crowning, and polishing (aka, L/C/P in the shorthand we use to fill out the job ticket). The fret material is made by rolling a rod of nickel-silver through a set of rollers, which gives a 0.050" by 0.225" or so bar-shaped fret with slightly rounded top and bottom edge...the fret stock is hammer-set into slots which are usually a bit narrower than the stock, providing a wedging action that makes for a stiff neck without the need for a truss rod. As Mr. Breakstone mentioned, it also makes for a 2.5-3x multiplier on a refret for mere mortals. Even a busy shop is unlikely to see more than a few of these a year, so it is a skill set which is seldom used.

My question was directed primarily at repair people (although thanks for your reply!) after a discussion with one of our customers that has become convinced by some unnamed internet authority that milling his brand new, lovely bar frets from 0.048" down to about 0.028" would make the world a better place and lower health insurance premiums for everyone. I left the discussion after mentioning to the customer that the guitar came to us with 0.030" height or lower...and questioning whether he really wanted us to bill him another 2-3 hours to undo the other 7 hours of work (at $110/hour bench rate).

The boss finally convinced the customer to go no lower that 0.037" - the older Martin spec - but even then, it seems like such a waste. If I work tomorrow (I may just pack and head home to bed instead, given my ears are still blocked), I suspect I'll be providing some of the motive power for the job. Ugh...

Thanks, Mr. Breakstone - I am hoping for the best.

_________________
For the times they are a changin'

- Bob Dylan



These users thanked the author Woodie G for the post (total 2): Hesh (Sun Dec 08, 2019 9:11 am) • Pmaj7 (Sat Dec 07, 2019 11:14 pm)
Top
 Profile  
 
PostPosted: Sat Dec 07, 2019 8:05 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat May 22, 2010 10:32 am
Posts: 2616
First name: alan
Last Name: stassforth
City: Santa Rosa
State: ca
Zip/Postal Code: 95404
Country: usa
Focus: Build
Status: Amateur
Thanks Woodie and Chris for clarifying that.
Learn something new here everyday, almost.
Alan


Top
 Profile  
 
PostPosted: Sun Dec 08, 2019 3:49 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Sep 08, 2010 12:17 am
Posts: 1286
First name: John
Last Name: Arnold
City: Newport
State: TN
Zip/Postal Code: 37821
Country: USA
Focus: Repair
Status: Professional
Fret height is about personal preference. I prefer 0.040" for bar frets, with a maximum of 0.045". Anything higher than that tends to be too 'catchy' when sliding. Conversely, lower than around 0.032" requires too much finger pressure for a clean note.

With regards to the life of the frets, IMHO it is hard to beat the durability of the original Martin frets, reputedly because of the 30% nickel content. Typical frets today are 18% nickel. I don't know if anyone is offering that material for bar frets today; a Google search seems to indicate it is an obscure alloy that is generally called cupro-nickel 715, not nickel-silver.

_________________
John



These users thanked the author John Arnold for the post (total 4): dpetrzelka (Mon Dec 09, 2019 3:53 pm) • Pmaj7 (Mon Dec 09, 2019 3:46 pm) • Woodie G (Sun Dec 08, 2019 9:35 pm) • Clinchriver (Sun Dec 08, 2019 7:34 pm)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: Michaeldc and 64 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com