Official Luthiers Forum!
http://w-ww.luthiersforum.com/forum/

Number 3 Celtic themed 12 fret 000
http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10101&t=52976		 Page 1 of 1
Author:  Bob Orr [ Thu Feb 27, 2020 1:08 pm ]
Post subject:  Number 3 Celtic themed 12 fret 000
Celtic Themed 12 fret 000. Made Nov 2019 to Feb 2020.
This is guitar number 3. I wanted to use local timer as much as I could and went with a celtic theme for the decoration. Scoop cutaway and arm bevel. I followed Hesh’s method of setting the neck angle and set up that he has posted on here and it came our bang on first time around with a really tight neck join. Frets were pressed in and barely needed much dressing at all and there is no hump! Thank you again Hesh for sharing this. There are quite a few cosmetic mistakes I am aware of and hope to improve on these with the next one. I am keeping this one, it sounds pretty good to me and has only been strung for a couple of days
Back and sides ; locally sourced quarter sawn English oak
Soundboard ; European alpine spruce
Bindings back strap and heel veneer; leopardwood
Purflings; bwb on sides double row of bwb on top and back
Fingerboard, headstock, faceplate and bridge; bog oak.
Inlays; MOP celtic knot on headstock, celtic dragon of abalone and tagua nut at twelfth fret and soundhole is 84 pieces of hand cut maple veneer set into a bog oak dust and epoxy mix. I was going to buy one of the lovely celtic soundholes from Petros Guitars but with the poor exchange rate and extortionate postage costs to UK it was way out of my budget.
Tuners; Wilkinson open.
Attachment:
Front.JPG
Attachment:
back.JPG

Attachment:
scoop cutaway.JPG
Attachment:
arm bevel.JPG

Attachment:
soundhole.JPG

Attachment:
neck joint and sound port.JPG
Author:  Bryan Bear [ Thu Feb 27, 2020 1:19 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Great job on that rosette! There are a lot of ambitious elements in there for a 3rd guitar. My 3rd instrument was my first bound instrument. I was nowhere near ready to do an armrest bevel or cutaway scoop. Well done.
Author:  Bob Orr [ Thu Feb 27, 2020 2:07 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Bryan Bear wrote:
Great job on that rosette! There are a lot of ambitious elements in there for a 3rd guitar. My 3rd instrument was my first bound instrument. I was nowhere near ready to do an armrest bevel or cutaway scoop. Well done.


My first a black walnut Reso had a scoop cutaway too!
Attachment:
007 (300x199).jpg
Author:  johnparchem [ Thu Feb 27, 2020 2:25 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Nice looking guitar!
Author:  Bob Orr [ Thu Feb 27, 2020 4:21 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Here are closeups of the inlays.
Attachment:
Headstock.JPG

Attachment:
12 fret inlay.JPG
Author:  Joe Beaver [ Thu Feb 27, 2020 4:35 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Very well done!!! I love the look of the guitar, and especially the inlays. Are they your design?
Author:  Bob Orr [ Thu Feb 27, 2020 5:05 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Joe Beaver wrote:
Very well done!!! I love the look of the guitar, and especially the inlays. Are they your design?


I got them from the internet by Googling Celtic knots. The dragon is much simplified!!!! Copied the jpegs into a word document and resized them to what i needed. then made several copies of each and used these to cut the inlays and pieces.
Author:  meddlingfool [ Thu Feb 27, 2020 6:29 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Nice!
Author:  Colin North [ Fri Feb 28, 2020 6:02 am ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Nice Job Bob!
Author:  DannyV [ Sat Feb 29, 2020 12:10 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Love it!!!
Author:  Bob Orr [ Sat Feb 29, 2020 4:41 pm ]
Post subject:  Re: Number 3 Celtic themed 12 fret 000
Thanks for the comments guys, much appreciated.
Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/