Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sat Nov 23, 2024 4:41 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Tue Apr 12, 2022 6:35 pm 
Offline
Walnut
Walnut

Joined: Fri Mar 04, 2022 7:04 pm
Posts: 5
First name: Michael
Last Name: Stroud
City: Cedar Creek
State: TEXAS
Zip/Postal Code: 78612
Country: United States
Focus: Build
Status: Amateur
So the instructions for Brite Tone say to spray with temps between 65 and 75. Nearly impossible here in Texas this close to summer. Would it be acceptable to spray in the morning when the temp is lower (assuming the humidity is around 60%) and then move the item into the house to dry? Then rinse and repeat until I get the required amount of coats (planning on 10-12). The house stays a pretty constant 73-75 with humidity around 50%, just can't spray in the house.

Thanks in advance!

Michael


Top
 Profile  
 
PostPosted: Thu Apr 14, 2022 8:13 am 
Offline
Koa
Koa

Joined: Tue Jan 22, 2008 8:57 pm
Posts: 762
Location: Austin, Texas
I think those instructions apply mainly to what's happening during and immediately after spraying...e.g. if you lay the coat on in good conditions you probably don't have to bring it inside unless you want to...there will still be solvents flashing off during curing so I'd suggest if you really feel the need to bring it in then take it to the garage. being out of the direct sun is far more important than the actual temperature

the issue with high humidity is that if the finish sets up too quick the moisture can get trapped and cause blushing (turning white)...high temps don't let the product flow out and level itself and in extreme cases I guess it can start to dry in the air before it hits the work. low temps are also an issue but I've found that placing some 500W halogen work lights (with sealed lenses) in the area works fine and in a pinch (you've got a schedule, you're spraying in the garage, it's below freezing outside and the 8 halogens you've got spread around aren't enough) pre-heating the product works great...never tried putting a rattle can in a pot of hot water though, just my spray gun cup


Top
 Profile  
 
PostPosted: Thu Apr 14, 2022 8:32 am 
Offline
Koa
Koa

Joined: Sat Mar 09, 2019 4:50 pm
Posts: 1251
Location: Goodrich, MI
First name: Ken
Last Name: Nagy
City: Goodrich
State: MI
Focus: Build
Status: Amateur
I did a Z-poxy inlay pool (like clear mastic) on my arch top in the winter in my basement. It isn't supposed to work. I got it warm with the heat gun, and poured the poxy in. Then I finished it with 2 thin coats of Z-poxy, with a couple bits of oil paint on a toothpick for toning; after heating with the gun. It was probably just below 50 degrees. It worked. I did move the guitar upstairs after the finish coats. It was almost 20 degrees warmer up there.

I didn't follow any rules besides mixing well.

I wonder how it works in the summer!

_________________
Why be normal?


Top
 Profile  
 
PostPosted: Thu Apr 14, 2022 8:46 pm 
Offline
Walnut
Walnut

Joined: Fri Mar 04, 2022 7:04 pm
Posts: 5
First name: Michael
Last Name: Stroud
City: Cedar Creek
State: TEXAS
Zip/Postal Code: 78612
Country: United States
Focus: Build
Status: Amateur
Thanks! I will give it a try.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 56 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com