| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Truss Notch Cutter http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10101&t=55652 |
Page 1 of 1 |
| Author: | Mike OMelia [ Sun Apr 30, 2023 4:06 pm ] |
| Post subject: | Truss Notch Cutter |
https://www.stewmac.com/luthier-tools-a ... gK33vD_BwE Great tool. But I wish it had a smaller cutter. Thoughts? Something more suitable for smaller pegheads (mandolins?) Can I get a smaller version of that cutter? |
|
| Author: | Barry Daniels [ Sun Apr 30, 2023 4:12 pm ] |
| Post subject: | Re: Truss Notch Cutter |
McMaster-Carr has them. |
|
| Author: | Clay S. [ Mon May 01, 2023 9:06 am ] |
| Post subject: | Re: Truss Notch Cutter |
You could use a W.L. Fuller four flute countersink and chisel the taper flat to give a square shoulder. Find a countersink without the set screw collar such as this type (or file off the collar of those that have it): https://hardwickandsons.com/products/w- ... ag_organic |
|
| Author: | Barry Daniels [ Mon May 01, 2023 11:25 am ] |
| Post subject: | Re: Truss Notch Cutter |
That is a really cool hardware store Clay. They have good prices and some hard to find tools. |
|
| Author: | rbuddy [ Mon May 01, 2023 1:20 pm ] |
| Post subject: | Re: Truss Notch Cutter |
Look for counterbore's or type R counterbores. |
|
| Author: | Clay S. [ Mon May 01, 2023 2:09 pm ] |
| Post subject: | Re: Truss Notch Cutter |
Hi Barry, That is an interesting store - thanks for pointing that out. Brian - I should have looked a little farther. They do have counterbores - a few more bucks, but not too expensive: https://hardwickandsons.com/collections ... ounterbore |
|
| Author: | Gary Davis [ Tue May 02, 2023 7:53 am ] |
| Post subject: | Re: Truss Notch Cutter |
Only a ten-hour drive for me to the store but its right on my route from home to the boat moored in Bellingham. Definitely checking it out next time through. |
|
| Author: | rbuddy [ Tue May 02, 2023 10:03 am ] |
| Post subject: | Re: Truss Notch Cutter |
Here is a smaller one - https://www.jamestowndistributors.com/product/product-detail/500 Jamestown used to have several different sizes, and I've ordered some from them before. |
|
| Author: | pullshocks [ Tue May 02, 2023 5:43 pm ] |
| Post subject: | Re: Truss Notch Cutter |
Barry Daniels wrote: That is a really cool hardware store Clay. They have good prices and some hard to find tools. Yeah, Hardwicks is great. It was a sad day when they moved out of Seattle (sad for me, not necessarily sad for them). Sent from my iPhone using Tapatalk |
|
| Author: | Mike OMelia [ Fri May 05, 2023 2:41 pm ] |
| Post subject: | Re: Truss Notch Cutter |
Just asking, are any of these compatible with the stew-mac system? The rod diameter is my concern (and locking in to it). Nice if someone here has done that... |
|
| Author: | Dan Miller [ Fri May 05, 2023 4:44 pm ] |
| Post subject: | Re: Truss Notch Cutter |
If it doesn't fit the SM shaft, you could just get some drill rod of the appropriate diameter to fit the counterbore. |
|
| Author: | Clay S. [ Fri May 05, 2023 6:40 pm ] |
| Post subject: | Re: Truss Notch Cutter |
The counterbores list the diameter of the center hole. You can use an extra long drill bit chucked into drill backwards or a drill rod as mentioned. Such as: https://www.amazon.com/COMOWARE-Long-Dr ... WV1OIITOXD |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|