Official Luthiers Forum!
http://w-ww.luthiersforum.com/forum/

I processed some of the Brazilian rosewood…
http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10101&t=56395		 Page 1 of 1
Author:  Brad Goodman [ Sat Feb 10, 2024 3:23 pm ]
Post subject:  I processed some of the Brazilian rosewood…
I started cutting up the Brazilian as carefully as I could...

So far I got about 40 fretboards 50 bridge blanks six sets of sides two sets of backs and I barely made a dent in it lol.
I'm so excited about it. I actually started building a guitar out of it a jazz classical.Image
This is the biggest board of the batch it is 6 1/2 feet long. It averages 11 inches wide and it is an inch and a quarter thick there is not one little crack in it and maybe about two little worm holes on one edge lol.
It's gonna be hard for me to cut into this board, but I'm gonna have to sooner or later.
Image
Image

Here's some of the back sets, sides, and fretboards
Image
Image
Image
Author:  meddlingfool [ Sat Feb 10, 2024 3:33 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
Nice!
Author:  bcombs510 [ Sat Feb 10, 2024 3:34 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
Such a nice score, awesome.


Sent from my iPhone using Tapatalk Pro
Author:  edstrummer [ Sat Feb 10, 2024 4:57 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
Pretty awesome. You’re very fortunate to have that board. I’ll bet it wasn’t cheap even if it was a while ago that you acquired it.


Sent from my iPad using Tapatalk
Author:  Darrel Friesen [ Sat Feb 10, 2024 6:08 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
Nice stuff Brad. I don't hate you. :)
Author:  Brad Goodman [ Sat Feb 10, 2024 9:13 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
edstrummer wrote:
Pretty awesome. You’re very fortunate to have that board. I’ll bet it wasn’t cheap even if it was a while ago that you acquired it.


Sent from my iPad using Tapatalk


I just got it 3 weeks ago....

I made the guy an offer he couldn't refuse 8-)
Author:  mikemcnerney [ Mon Feb 12, 2024 9:29 am ]
Post subject:  Re: I processed some of the Brazilian rosewood…
Brad what blade and the specs, and what machine are you using. I was just told about the highland blade available in 1/2" and 3/4" with a .032 kerf which sounds really good. And typically how much are you losing to sanding?
Author:  Brad Goodman [ Mon Feb 12, 2024 7:48 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
mikemcnerney wrote:
Brad what blade and the specs, and what machine are you using. I was just told about the highland blade available in 1/2" and 3/4" with a .032 kerf which sounds really good. And typically how much are you losing to sanding?


I have a 4.5 HP 24" laguna bandsaw....

I use (and swear by) a 1" wide Lenox carbide tipped Woodmaster blade-the kerf is.060-This blade has lasted many years and still cuts ebony, Ziricote, rosewood,etc. like butter!!

I have tried several different blades and have not been happy with the results-especially plain steel blades.

I try to cut the backs at around .160 ( .110 -.115 finished after joining) and the sides at around .140 (.090 finished)-I have found that if I go any thinner I always regret it.

I can cut the sides a little tighter because they don't have to joined which also loses some thickness.

My theory is I would rather cut a little thick than ruin a set.
Author:  meddlingfool [ Mon Feb 12, 2024 8:04 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
five slices per inch or bust!
Author:  Brad Goodman [ Mon Feb 12, 2024 9:03 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
meddlingfool wrote:
five slices per inch or bust!


In a perfect world -yes
Unfortunately I don't live in one-Theoretically if you have a perfectly flat board, but they never are.. so I always joint one face so, it is no longer a full inch.
Author:  Darrel Friesen [ Mon Feb 12, 2024 9:08 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
Brad Goodman wrote:
meddlingfool wrote:
five slices per inch or bust!


In a perfect world -yes
Unfortunately I don't live in one-Theoretically if you have a perfectly flat board, but they never are.. so I always joint one face so, it is no longer a full inch.


I err on that side as well Brad although I love a Timberwolf, 1/2" 3 TPI steel blade for the two, three or four sets a year that I do on my 17" 2 HP saw. I've actually gotten 5 slices per inch but then I have an odd man out! :)
Author:  meddlingfool [ Mon Feb 12, 2024 9:17 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
That’s why I buy 5/4 or 8/4, but I guess when it’s a barn find ya take what you can get…:)
Author:  Darrel Friesen [ Mon Feb 12, 2024 9:25 pm ]
Post subject:  Re: I processed some of the Brazilian rosewood…
meddlingfool wrote:
That’s why I buy 5/4 or 8/4, but I guess when it’s a barn find ya take what you can get…:)

Hell yeah. It's what you do with what you got and it's not consistent for the most part.
Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/