| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Steps in making pegs http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10101&t=56894 |
Page 1 of 1 |
| Author: | Ken Nagy [ Wed Nov 20, 2024 9:31 am ] |
| Post subject: | Steps in making pegs |
I just made some pegs. I have 2 that still don't have the head carved down yet. The first step is the rough turning. Attachment: IMG_2049.jpg Then I change jaws, and turn the head to the approximate shape. At this point the button is done, because it had the taper, and the groove for the tail gut cut, on the first side.I just round out the other side, Attachment: IMG_2050.jpg Then I cut the taper, and carve in the shoulder. It will need shimming to get it true again. If it isn't perfect, no one will know that the head is .002" off. I use the cutting tool to mark the 2 grooves. I cut with files. Then I polish it all up. Attachment: IMG_2051.jpg Now the head needs to be carved down. You could use the round end of a belt sander. It is concave north/south, and convex east/west. I used a knife. It worked great. Not much dust. Attachment: IMG_2052.jpg I smoothed it up by scraping. The shape is by feel. The edges should all be about the same, to about the widest point. It should look even. Attachment: IMG_2054.jpg Then it needs the carving that makes it look like a heart. I start with an X-acto cut for the centerline; then carve away with a 6mm chisel. I could use a 3mm chisel. Attachment: IMG_2055.jpg This is a shot showing the shape: Attachment: IMG_2058.jpg I finish with CA pore fill. I brush some iron acetate in the area between the collar and the head, to darken it so it recedes out of view. Polished with micromesh. This is almost complete filling; better than it was. I'll leave it like that so it looks like wood. They feel nice. Attachment: IMG_2059.jpg
|
|
| Author: | bobgramann [ Wed Nov 20, 2024 11:12 am ] |
| Post subject: | Re: Steps in making pegs |
Beautiful. Thank you for the tutorial. |
|
| Author: | bionta [ Wed Nov 20, 2024 3:46 pm ] |
| Post subject: | Re: Steps in making pegs |
Those are beautiful, Ken. So much attention to detail in a small part that probably makes a big impression on the player. |
|
| Author: | Dave Rickard [ Wed Nov 20, 2024 4:41 pm ] |
| Post subject: | Re: Steps in making pegs |
Way cool Ken. Thanks for the tutorial. |
|
| Author: | Colin North [ Wed Nov 20, 2024 7:09 pm ] |
| Post subject: | Re: Steps in making pegs |
Lovely, really nice work. |
|
| Author: | bftobin [ Fri Nov 22, 2024 8:06 pm ] |
| Post subject: | Re: Steps in making pegs |
Great tutorial Ken. I've been thinking about making a flamenco with pegs instead of machine turners. |
|
| Author: | Ken Nagy [ Sat Nov 23, 2024 9:14 am ] |
| Post subject: | Re: Steps in making pegs |
Brent, I'm finishing up some pegs I made for a small Torres. The original had pegs. I think I used the cream colored part of a board labeled "Royal Ebony." I think it is Katalux. But it could be something different. Pegs don't have to be real hard; they can wear out the hole then; if they aren't really smooth, and have some lube. Walnut, cherry, maple, can all be used. Often I match the pegs and the fingerboard. The fretboard on the Torres is a purplish Katalux. Something interesting is nice if you are going to the trouble to make them. On these, the stock was narrow, a little over 3/4" I like them wider. The one think I don't like about what I did is the undercut is too wide. I think I was having trouble with he knife slipping and nipping the collar. It wasn't a good idea. What was a good idea, is the way I didn't the last ones. Cut a line down the middle with a knife, and whittle away at the curve with a sharp chisel. Twist the chisel to smooth the bottom up. Even my 6 mm chisel didn't mar up the collar. It looks like I made the 1/8" rounded chisel for the u'cut out of the shank of an old 5/16" HSS end mill! Attachment: IMG_2070.jpg Attachment: IMG_2069.jpg Attachment: IMG_2068.jpg
|
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|