Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Wed Dec 04, 2024 10:32 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject:
PostPosted: Thu May 10, 2007 2:35 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 01, 2006 3:25 am
Posts: 3788
Location: Russellville, Arkansas
Today I was playing around with a junky old Harmony six string. I want it to take and leave at the cabin.

It's a ladder-braced plywood jobbie, and ugly as sin. The belly is torqued, neck needs a reset, and it had this awful thick black plastic pickguard on it, held on with five black screws.

I needed a pickguard somewhat smaller than the Martin style I stock, but still large enough to cover all five screw holes. You guessed it, this guitar got a cut down pickguard.

After determining the arc needed inside the guard, I set up my Fly cutter. You can get 'em at most hardware stores. I pre-drilled a hole in 3/4 plywood and skimmed the surface with the cutter. That told me where to align the pickguard for surgery.

I then used blue masking tape and taped down the major edges, including the slim inside piece that got trimmed off. It was tedious but took only twenty seconds to sever a perfect-cut curve off the D size guard. Looks great. (for a junker)

Tomorrow it gets a quick saddle and set of strings before we leave for the cabin. Yahoo, music on the mountain. You can find it by looking on Spring Lake Road after finding Mt. Magazine, Arkansas. About six miles or so ENE. Twang!

_________________
http://www.dickeyguitars.com


Top
 Profile  
 
 Post subject:
PostPosted: Thu May 10, 2007 6:47 pm 
Offline
Koa
Koa

Joined: Wed Sep 28, 2005 2:58 am
Posts: 552
Location: Canada
Another easy way to cut an accurate (& clean) ark in pick guard material is to set up a (sharp pointed) pair of dividers to the correct radius... Then tape down the blank on a piece of scrap MDF or whatever. Fumble around with the pivot point of the dividers to get the arc where you want it & then use the other point to scribe your way through the pick guard. Works a treat!


Top
 Profile  
 
 Post subject:
PostPosted: Thu May 10, 2007 11:03 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Sep 09, 2005 7:51 am
Posts: 3786
Location: Canada
I use and exacto knife and a 4 inch can bottom edge. The can also acts as the clamp when you lean on it. Takes all of 6 seconds to do ...

_________________
Tony Karol
www.karol-guitars.com
"let my passion .. fulfill yours"


Top
 Profile  
 
 Post subject:
PostPosted: Fri May 11, 2007 12:56 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 01, 2006 3:25 am
Posts: 3788
Location: Russellville, Arkansas
There you go, three ways to do a simple job.

_________________
http://www.dickeyguitars.com


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 52 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com