Official Luthiers Forum!
http://w-ww.luthiersforum.com/forum/

Fret Blades
http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10102&t=14688		 Page 1 of 1
Author:  Shane Neifer [ Sun Nov 25, 2007 4:59 pm ]
Post subject: 
MAN!! Where does time go? I have had these blades for a while now. I have them wrapped. See.....!!!



So I need addresses. The list of those who previously expressed interest are:

Dan Vincent
Steve Walden
Gary Cote
Jim Womack
Peter Joseph
Waddy Thompson
Mike Mahar
Dave Anderson
Dave Rickard
Michael Lloyd

So please confirm that you still want them and PM or e-mail me your address if I don't have it already. They are $49 including shipping.

If anyone else is interested, these table saw blades are .024 kerf, 6" diametre for a 5/8" arbor and look like this:



Thanks!

Shane
Author:  JimWomack [ Sun Nov 25, 2007 10:45 pm ]
Post subject: 
Sorry Shane, I must be coming down with old timers disease.  Check your email for payment/address details.
Author:  Peter J [ Mon Nov 26, 2007 12:07 am ]
Post subject: 
Hello Shane,

An email with my address and another with the payment should be in your mailbox. Thanks as always.

Peter
Author:  WaddyThomson [ Mon Nov 26, 2007 12:36 pm ]
Post subject: 
Shane, thanks for the reminder.  I guess the swapmeet clouded my memory.  Check your email for paypal.
Author:  Dave Anderson [ Mon Nov 26, 2007 1:41 pm ]
Post subject: 
Thanks Shane, I sent you an email.
Author:  Rick Turner [ Mon Nov 26, 2007 3:06 pm ]
Post subject: 
Got more?   And if so, what's the diameter and bore size?
Author:  Bruce Dickey [ Mon Nov 26, 2007 4:10 pm ]
Post subject: 
Shane Sez in the thread above:

If anyone else is interested, these table saw blades are .024 kerf, 6" diametre for a 5/8" arbor and look like this:
Author:  Shane Neifer [ Mon Nov 26, 2007 8:51 pm ]
Post subject: 
[QUOTE=Rick Turner] Got more?   And if so, what's the diameter and bore size?[/QUOTE]

Yup, lots more (relatively speaking of course!!))

Thanks Bruce for pointing out the particulars!

6 inch diamtre, about 110 teeth, .0245 kerf +/- .0005, and a 5/8" bore. These blades are specially made to these specs and their tolerances are twice as good as jeweler's blades which has the kerf at +/- .001.

Thanks

Shane
Author:  charliewood [ Tue Nov 27, 2007 7:20 am ]
Post subject: 
Shane
While Im not in a position to get any extra stuff from you than Ive already ordered this time,
But next order Ill definitely take one of those,,,
Man, Im so glad I have someone as close as you are to me, selling the kinds of things that you are offering now - Good Job!
Cheers
Charlie
Author:  Steve Walden [ Tue Nov 27, 2007 3:53 pm ]
Post subject: 

Shane - I think you sent mine with my swap meet stuff.  I remember seeing a folded cardboard in the box.  I may need another to make kerfed linings, or is that kerfing.....or is it kerfling?


Just kidding about the linings.  But, if you need to unload one more I will take it.


Thanks,
Author:  Shane Neifer [ Wed Nov 28, 2007 3:38 am ]
Post subject: 
Hey Steve,

I do have quite a few more but it is totally up to you if you want another.

Thanks

Shane
Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/