| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Tablesaws again http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10102&t=8120 |
Page 1 of 1 |
| Author: | Louis Freilicher [ Tue Aug 22, 2006 1:01 pm ] |
| Post subject: | |
Hey Folks, I'm looking to upgrade my tablesaw and I want to know if anybody has heard anything about the new Grizzly 2 HP Hybrid Cabinet Saw? www.grizzly.com/ products/G0478 I want something powerful enough to be a good all around machine but also accurate enough to slot fingerboards. Thanks for the input and inspiration, Louis |
|
| Author: | Joe Beaver [ Tue Aug 22, 2006 2:32 pm ] |
| Post subject: | |
I'm planning to upgrade my tablesaw also. I haven't bought yet but I've done a lot of looking. This is the one I've decided on. Just waiting to see if it goes on the fall sale list. http://www.grizzly.com/products/G1023Z |
|
| Author: | Louis Freilicher [ Tue Aug 22, 2006 3:39 pm ] |
| Post subject: | |
Opps!! |
|
| Author: | Louis Freilicher [ Tue Aug 22, 2006 3:39 pm ] |
| Post subject: | |
Thanks for the advice Todd. I'm not dead-set on the hybrid concept, the saw looked very attractive for the money. Your point about R&D is a good one. I am looking for the saw that will last for the rest of my working life. Louis |
|
| Author: | Brock Poling [ Tue Aug 22, 2006 4:14 pm ] |
| Post subject: | |
[QUOTE=Joe Beaver] I'm planning to upgrade my tablesaw also. I haven't bought yet but I've done a lot of looking. This is the one I've decided on. Just waiting to see if it goes on the fall sale list. http://www.grizzly.com/products/G1023Z[/QUOTE] I just bought this saw in the 5hp version (right tilt). It is very nice. I plan on doing a full review in a couple of weeks. :-) |
|
| Author: | Joe Beaver [ Tue Aug 22, 2006 4:26 pm ] |
| Post subject: | |
Brock, Good Deal! I'll be watching for it. |
|
| Author: | Scooter B [ Wed Aug 23, 2006 1:28 pm ] |
| Post subject: | |
Fine Woodworking www.finewoodworking.com June 2006 issue had a review of 10" cabinet saws. If you can track one down it may be benificial to you. Top honors went to Powermatic PM2006 at $2100 and Sawstop 31230 at $3270 Best value went to Grizzly G1023SL at $975 but the blade and miter slots were out of parallel and required adjustments. I just have a Delta contractors saw  |
|
| Author: | Joe Beaver [ Wed Aug 23, 2006 2:01 pm ] |
| Post subject: | |
Scooter, Me too. A 40 year old delta contractors saw at that!! |
|
| Author: | mikev [ Wed Aug 23, 2006 2:13 pm ] |
| Post subject: | |
i had the grizley 1023sl.. and i added the router table to the top.. i was able to adjust the table parallel to within .0015 full lenght of the top. It was easy to do, stayed put and was a great saw.. I can not speak for any of the other saws since i didn't own them, but the griz was very accurate, smooth and powerful. I think it was a great value. Mike |
|
| Author: | Scooter B [ Thu Aug 24, 2006 3:03 am ] |
| Post subject: | |
[QUOTE=Joe Beaver] Scooter, Me too. A 40 year old delta contractors saw at that!![/QUOTE] Thanks Joe I'm glad I am not the only one slumming it here on the machinery side. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|