Dang, just when you think you had a new idea!
| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Cutting Sides with a CNC http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10106&t=11055 |
Page 1 of 1 |
| Author: | Parser [ Thu Feb 22, 2007 10:27 am ] |
| Post subject: | |
I've had some good success recently using my CNC machine to profile acoustic guitar sides prior to bending. By this I mean that I've used a few CAD tricks in order to get the precise curve that the bottom edge of an acoustic side makes if you straighten it out. I.e, this means that after gluing the end blocks on I will only have to make minimal corrections via sanding in order to prep the sides for gluing the top and back on. I bent some mahogany sides the other day and it looks like this is going to work very well. Cool stuff - does anyone else have any experience with this? I've been trying to think about ways to revamp the building process now that I have the CNC... |
|
| Author: | Don Williams [ Thu Feb 22, 2007 10:49 am ] |
| Post subject: | |
I'm SO envious. Taylor does that with their sides too. |
|
| Author: | Parser [ Thu Feb 22, 2007 11:50 am ] |
| Post subject: | |
Dang, just when you think you had a new idea!
|
|
| Author: | Brad Way [ Thu Feb 22, 2007 11:51 am ] |
| Post subject: | |
Trev...I have not used CAD to precut sides but I did work on a project several years ago where I used 3D modeling and the "sheet metal" functions to design 3D opjects and then "un-wrap" the models into 2 dimensional full scale drawings. I worked very well. I am sure this could be done for what you are talking about. I will try it in Solidworks and see what happens. |
|
| Author: | Parser [ Thu Feb 22, 2007 1:10 pm ] |
| Post subject: | |
I'm doing that exact thing in rhino using the "unroll developable surface" command. SW is great for mechanical design, but I'm really really enjoying Rhino for the artsy stuff. |
|
| Author: | Brad Way [ Thu Feb 22, 2007 1:41 pm ] |
| Post subject: | |
Actually I used the sheet metal command in Microstation...it was a really difficult 3D package but it worked. I have been playing with Solid Works and can't figure it out...but I will!  By the way..have you checked out the Taylor Factory Friday video's? Check out how they side bend with precut sides...cool stuff.
|
|
| Author: | Parser [ Thu Feb 22, 2007 2:07 pm ] |
| Post subject: | |
I remember seeing the side bending machine..but I didn't remember seeing that they had done that. Those factory friday's are great, Taylor must be a cool company to do release something like that. The guitar industry is certainly different from other industry.. |
|
| Author: | John Watkins [ Fri Feb 23, 2007 12:21 am ] |
| Post subject: | |
I've done templates for a number of my customers in the same manner. I've found that the trick to doing it accurately is to provide the bending molds as well. That way you can control the position of the slot at the waist and use it to index the side in the bender. |
|
| Author: | Parser [ Fri Feb 23, 2007 3:04 pm ] |
| Post subject: | |
I've found that if you start bending at the back of the side and work your way up it works pretty well (I'm using a bending iron at the moment). I am using a mold that I CNC cut as well, so I know that my side surface is as accurate as possible. Fun stuff.. |
|
| Author: | Bob Garrish [ Sat Feb 24, 2007 6:39 am ] |
| Post subject: | |
I've been wondering about ways to index the sides when the profiles are CNC cut. I was considering using a two-bend system like Taylor does (bend from flat to waisted then use the waist bend to re-index and bend bouts). It's more work, but it seems like it would give more accurate side bends -> less sanding. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|