Bob's right. ER25 does go up to 5/8"....almost every day...
| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| HSD Router Spindle http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10106&t=17991 |
Page 1 of 1 |
| Author: | npalen [ Mon Jul 14, 2008 2:09 pm ] |
| Post subject: | HSD Router Spindle |
[url][/url]http://www.shopbottools.com/spindles.htm Wondering if an of you guys have seen the HSD spindle in the flesh? Wondering about performance on the 2.25HP in particular. Thanks Nelson |
|
| Author: | Sheldon Dingwall [ Wed Jul 16, 2008 11:49 am ] |
| Post subject: | Re: HSD Router Spindle |
npalen wrote: [url][/url]http://www.shopbottools.com/spindles.htm Wondering if an of you guys have seen the HSD spindle in the flesh? Wondering about performance on the 2.25HP in particular. Thanks Nelson I've never heard anything bad about HSD. Have you posted this question on the Shopbot forum? I recall reading someone's experience with that size and thinking that would be fine for guitars. The only question is can it accept a 1/2" shank bit. |
|
| Author: | npalen [ Wed Jul 16, 2008 8:07 pm ] |
| Post subject: | Re: HSD Router Spindle |
Good idea on the Shopbot forum I believe the 2.25 HP (1.5KW) version has a ER25 collet nose which should handle a 1/2" shank. |
|
| Author: | Jim Watts [ Wed Jul 16, 2008 9:33 pm ] |
| Post subject: | Re: HSD Router Spindle |
Nelson Heres another spindle company too. I spoke with once about a spindle and if I remember right they're prices were pretty good. www.ekstromcarlson.com/spindle%20motors.htm I'd be pretty confident that a 2-1/4 hp would way more than enough power assuming a continuous rating. I bet they have a power curve available for as it's a real spindle. |
|
| Author: | Bob Garrish [ Wed Jul 16, 2008 9:38 pm ] |
| Post subject: | Re: HSD Router Spindle |
npalen wrote: Good idea on the Shopbot forum I believe the 2.25 HP (1.5KW) version has a ER25 collet nose which should handle a 1/2" shank. You can even squeeze an extra bit of love out of it as I'm pretty sure ER25 goes all the way to 5/8". |
|
| Author: | npalen [ Thu Jul 17, 2008 3:02 pm ] |
| Post subject: | Re: HSD Router Spindle |
[url][/http://www.talkshopbot.com/forum/messages/board-topics.htmlurl] Sheldon, I sure appreciate being pointed in the direction of the shopbot forum. What a wealth of info! Thanks for everyone for all the feedback! Nelson |
|
| Author: | npalen [ Thu Jul 17, 2008 3:03 pm ] |
| Post subject: | Re: HSD Router Spindle |
http://www.talkshopbot.com/forum/messages/board-topics.html There--I finally got it right! |
|
| Author: | John Watkins [ Fri Jul 18, 2008 10:29 am ] |
| Post subject: | Re: HSD Router Spindle |
Bob's right. ER25 does go up to 5/8"....almost every day...
|
|
| Author: | npalen [ Fri Jul 18, 2008 9:16 pm ] |
| Post subject: | Re: HSD Router Spindle |
I think you guys may need a vacation. 
|
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|