Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sun Nov 24, 2024 3:24 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Sun Dec 09, 2012 2:14 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Jun 21, 2008 10:58 am
Posts: 2774
Location: Tampa, Florida USA


Top
 Profile  
 
PostPosted: Sun Dec 09, 2012 3:01 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Jun 21, 2008 10:58 am
Posts: 2774
Location: Tampa, Florida USA
I use my mini mill and there isn't a problem with it. I don't see it being a problem for a drill press. Not really that much pressure to press a fret in my opinion if slotted correctly and with a lead filed in.
CA and glue will size the wood if somewhat spongy and the fret will hold better and be more solid. It's good for loose frets and will prevent dead sounding frets. It will also lube the fret slot and make pressing a little easier I guess too. Whether or not you use it is up to you in the end.
I made the video because I had to press this compound radius board and didn't have the time to make or cash for a set of cauls. I had given some thought to putting a bearing on the end of a shaft and roll it over the fret as it pressed it. But what the hell, the bolt and poly took about five minutes to make and worked fine. Beats noisy hammering and seems to follow the board radius.
I was just thinking out of the box again with this one and it just happened to work out this time and thought I'd share it. :)


Top
 Profile  
 
PostPosted: Mon Dec 17, 2012 1:51 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Sep 29, 2011 2:54 pm
Posts: 115
First name: Andrew
City: Ottawa
State: ON
Focus: Build
Status: Amateur
Thanks for posting, I think I might make myself one.
Any ideas for using it in a drill press without a sliding vice?


Top
 Profile  
 
PostPosted: Mon Dec 17, 2012 4:41 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Jun 21, 2008 10:58 am
Posts: 2774
Location: Tampa, Florida USA
I think you might try a pecking motion and as you raise up slide the board. Just as you would if you were hammering in frets except you are pressing it in. When you get to the ends you will want to go just past the edge of the board and press the overhang of the fret down slightly to set the ends. Just be careful not to over do it. Sort of like tapping the ends down when hammering in frets. You want to have the tail end of the frets bend down so it sets. You could try and press the ends first and work across the fretand see how that works out.
This method isn't the fastest or the best. It's just an alternative to hammering and another way of fretting as I see it.


Top
 Profile  
 
PostPosted: Wed Dec 19, 2012 3:13 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat May 12, 2007 6:11 am
Posts: 176
Location: Canada
I like the singer. Interesting idea too, chris.

_________________
Under Compensated Nut!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 18 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com