Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Nov 21, 2024 11:31 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: Guitar Troji plans
PostPosted: Fri Apr 09, 2010 7:59 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Jan 04, 2005 10:03 am
Posts: 6680
Location: Abbotsford, BC Canada
Well, seeing as the old thread on the guitar Troji has a dead link and I can't edit it, I thought it best to just start a new thread here.

So, you can download the plans here. The plans are drawn on 8.5"x11" paper so anyone with a basic printer can print them.

And for those who don't know what a guitar Troji is, here's a picture.

Image

_________________
My Facebook Guitar Page

"There's really no wrong way, as long as the results are what's desired." Charles Fox

"We have to constantly remind ourselves what we're doing....No Luthier is putting a man on the moon!" Harry Fleishman

"Generosity is always different in the eye of the person who didn't receive anything, but who wanted some." Waddy Thomson


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Wed Apr 21, 2010 10:34 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Feb 20, 2010 8:49 am
Posts: 110
First name: Bert
Last Name: Foster
City: Gainesville
State: GA
Zip/Postal Code: 30506
Country: United States
Focus: Build
Status: Semi-pro
Rod, Thanks I've been meaning to build one of these .

_________________
"Try to be the person your dog thinks you are."

http://sites.google.com/site/bertsguitarshop/


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Wed Apr 21, 2010 10:58 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Feb 28, 2009 10:34 pm
Posts: 1065
First name: Rob
Last Name: McDougall
City: Cochrane
State: Alberta
Hi Rod,

After building the Troji from your excellent plans, I built a mortising jig to fit on top.
I thought I would share as an add-on idea for those thinking of building the Troji.
Basically a tray with legs clamped to the Troji with a notch in the top for a pattern bit.
Cut my first mortise with it tonight and it seemed to work very well...

Image
Image
Image


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Sun Sep 08, 2013 6:29 pm 
Offline
Contributing Member
Contributing Member

Joined: Mon Dec 21, 2009 6:18 pm
Posts: 76
Location: Nacogdoches, Tx
First name: Bob
Last Name: Moore
City: Nacogdoches
State: Tx
Zip/Postal Code: 75965
Country: USA
Focus: Build
Status: Amateur
I was watching Todd Stock's videos on using Zpoxy for pore filling, and liked the look of the Troji that he used to hold the guitar while sanding it. Then I came across this thread and Rod's directions and plans. So I thought I'd use his directions and post pictures of the steps that I went thru in building it. I asked Rod's permission to post them here and he agreed. Thanks Rod.

Here are the major parts. The whole device used up about 3/4's of a sheet of plywood. Shown are the 2 sides, the base, and the long thin pieces are reinforcements for the sides. I spent around $90 for all the parts needed to build this.

Image

Next are the smaller parts. The shelf, a number of different sized "gussets"-used to help hold the side and the shelf vertical. Also, the shelf has a couple of pieces of plywood glued together with a T-nut that will be used to receive a threaded rod that will open and close the Troji. There are a couple of other supports too.

Image

The first thing I did was to assemble 6 of the gusset pieces to form two assemblies that go at the bottom of one of the sides.

Image

They were set 2" from the edge of that side at the bottom. I drew a line on the outside of the side to correspond with the thickness of the gussets and screwed them from the outside. The long side supports will hide most, if not all, the screws.

Image

One of the parts split up near the top, so the picture shows some clamps on that part after I used CA glue on the split.

Next, the shelf was assembled.

Image

You can see the hole on the shelf thru which the threaded rod will go. That support was made from 2 pieces of plywood glued together. I used a forstner bit to drill thru it. The T-nut is on the other side. I bought the wrong kind of T-nut. I wanted the kind that you hammer into the hole. But this one had two holes for screws, but there were no screws in the package. I found some, and used both the screws and some CA glue to hopefully bond it forever.


Image

Here's the side complete.


Image

For the other side, there's a hole near the middle of it where the threaded rod goes. There were 2 vertical and 2 horizontal supports, with one of the horizontal pieces having a hole in it for the handle rod to pass thru. I took care that both holes lined up, and glued and screwed (from the inside) that horizontal piece first. All of those pieces were glued, then I used screws from inside the side to further secure them.

Image

Initially, I set the hinges flush with the bottom of the side, then read in the directions that they need to overhang the side by about 1/8" to allow the side to open a bit wider, and re-set them. It took my wife and me to get this mounted as 2 hands aren't enough. But it's on there now. Oh, also, the side has to be mounted where the rod will go straight thru and catch on the T-nut attached to the shelf. I missed that mark the first time, but after sliding the hinges down and over, got it perfect the 2nd time around.

Image

Speaking of the handle. Here it is.

Image

The directions called for a threaded rod (length to be determined when installed), 2 nuts, 2 regular washers and a larger washer, all to be connected to the handle. I probably could have worked with that, but I put two nuts together on either side of the handle so that they'd lock in place and stay.

My wife took charge of cutting the foam pieces to size, and I used double sided tape and 3M adhesive to secure them to the sides and shelf, completing the Troji. I'm guessing 6-8 good hours of work to do all this.

Here it is, completed:

Image

I think I'll be pretty happy using this. There are several times where I need to work something on the sides, and this puts the guitar body at a good height and holds it securely.

Thanks for looking,
Bob

_________________
Bob
From the oldest town in Texas.


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Sun Sep 08, 2013 9:09 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Mar 24, 2006 12:42 pm
Posts: 2360
Location: Windsor Ontario Canada
First name: Fred
Last Name: Tellier
City: Windsor
State: Ontario
Zip/Postal Code: N8T2C6
Country: Canada
Focus: Build
Status: Amateur
After finishing mine 3 years ago I wonder why I didn't build one sooner. I had Rod's plans on my hard drive for a couple years but didn't get to it right away.

Another thanks to Rod for providing the plans
Fred

_________________
Fred Tellier
http://www.fetellierguitars.com
Facebook page http://www.facebook.com/pages/FE-Tellier-Guitars/163451547003866


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Mon Sep 09, 2013 9:15 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 03, 2006 1:47 pm
Posts: 1624
Location: United States
First name: Larry
Last Name: Hawes
Focus: Build
Status: Amateur
Nice tutorial thanks for posting that.

_________________
Thank You and Best To All


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Mon Sep 09, 2013 9:21 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 03, 2006 1:47 pm
Posts: 1624
Location: United States
First name: Larry
Last Name: Hawes
Focus: Build
Status: Amateur
I think I saw this online somewhere - converted my Work Mate to a Troji - works great.


You do not have the required permissions to view the files attached to this post.

_________________
Thank You and Best To All


Top
 Profile  
 
 Post subject: Re: Guitar Troji plans
PostPosted: Fri Jun 17, 2022 3:56 pm 
Offline
Mahogany
Mahogany

Joined: Mon Sep 22, 2008 6:27 pm
Posts: 76
Rod True, the link to the plans does not work. Can you make it available? Thanks, fred


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com