Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Wed Nov 27, 2024 10:46 pm


All times are UTC - 5 hours


Forum rules


Same rules apply to all forums at the Luthiers Forum.




Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: Baritone Uke Questions
PostPosted: Sun Aug 11, 2013 8:04 pm 
Offline
Walnut
Walnut

Joined: Sun Jul 14, 2013 10:41 am
Posts: 1
First name: Jerry
Last Name: Couch
City: Jackconville
State: AL
Zip/Postal Code: 36265
Country: USA
Focus: Build
Status: Amateur
Longtime lurker, first time builder, my first post and I'm seeking some advice

Building a baritone from plans from Ukulele World. Almost finished, but after reading some other threads on this forum, I have a couple of questions and concerns.

First-- I glued and screwed my neck to the body today. I used a straight edge to align the neck (without fret board) flush with the top of the body. I noticed some people use a 1 or 2 degree downward angle. Did I screw up.

Second--Got my frets, nut and saddle from StewMac, so I'm almost ready to do my fretting and setting the nut and saddle height. I've noticed that most builders advise to have .09" between the 12th fret and the strings. Does this apply to a baritone as well. I also saw a thread where one poster said to lay a 1/8" drill bit under the 14th fret and lay a straight edge from the nut to the 14th fret, and that shows the height of the saddle.

Third--I made it out of some black walnut I had laying around the shop, and I'm using a hard maple fret board, also some I had laying around the shop. I already have a soprano and a tenor, so I'm using Aquila nylgut strings (G,C,E,A) because I don't want to relearn all the chords. It's gonna be pretty, but what type of sound should I expect.

Fourth (and last)--Finishing? I've read that for the best sound, don't use any type of stain or varnish that will soak into the wood. I'm plan to use a cellulose based sanding sealer. I want a satin to low gloss finish, so what should I use.

Sorry for the long post, but can't go any further without consulting with someone more experienced than me.


Top
 Profile  
 
PostPosted: Mon Aug 12, 2013 8:40 pm 
Offline
Koa
Koa

Joined: Sat Nov 07, 2009 9:34 pm
Posts: 552
City: winnipeg
State: manitoba
Country: canada
Focus: Build
Status: Amateur
Jerry:
The first thing is RELAX!
Your ukulele will come out reasonable no matter how you do it. Make sure that your strings are low G. I ended up with high G for my brother's baritone and it loses the advantages of the big box. If you go for DGBE, you will play the same chords but you will be playing in a different key.

Build the bridge later. A straight-edge on the top of the frets should just kiss the front-edge of the bridge. Build the bridge to fit. Small adjustments can be taken up in the saddle.

An 1/8" clearance at the twelfth fret is a reasonable place to start. You can hone things down by messing with the nut-slots and saddle. Nylon strings are pretty forgiving on action.

For finishing, I use Danish-oil (instructions on the can) and several coats (5-ish) of wipe-on poly. It takes a month or so for the ukulele to get full voice.

Ukulele building is an adventure, enjoy the ride and the destination will take care of itself.

Bob :ugeek:


Top
 Profile  
 
PostPosted: Wed Aug 14, 2013 5:15 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Jan 27, 2013 4:30 pm
Posts: 7
Location: Queensland, Australia
First name: Colin
Last Name: Burge
City: Morayfield
State: Queensland
Country: Australia
Focus: Build
Status: Amateur
JelC50 wrote:
First-- I glued and screwed my neck to the body today. I used a straight edge to align the neck (without fret board) flush with the top of the body. I noticed some people use a 1 or 2 degree downward angle. Did I screw up.


The neck relief you mention, is primarlily used for when you have a radiussed (domed) soundboard. The reason being is that with a radiussed soundboard the saddle will sit a little higher which needs to be accounted for.

Cheers

Col


Top
 Profile  
 
PostPosted: Thu Aug 15, 2013 8:42 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2011 6:08 pm
Posts: 2712
First name: ernest
Last Name: kleinman
City: lee's summit
State: mo
Zip/Postal Code: 64081
Country: usa
Focus: Build
Status: Professional
I only radius the back I want a nice flat surface for FB and bridge , you can thin the edges by 10 to -20 thou if they are too thick e.g..100. I want my neck/body coplanar.I use 1, 8-32 bolt and glue together many ways to do it. Check out my uke videos for some useful tips www.atelierrtomistrings.com


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 36 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com