| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Carbon Fiber rods http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10128&t=42903 |
Page 1 of 1 |
| Author: | frwilliams [ Wed Mar 05, 2014 11:18 am ] |
| Post subject: | Carbon Fiber rods |
Can anyone tell me if the carbon fiber material they make archery arrows with is the same strength as material typically sold at Stew mac etc.. If it is, do you think the round shape if seated in a core box routed channel covered with a wood fillet would be good. I am trying to straiten a cheap mandolin neck with alot of upbow, remove the finger board, plane out bow, and rout and epoxy CF etc.. needless to say no truss rod in it. I have a cheap source of old arrows locally. thanks rasby |
|
| Author: | Chris Pile [ Wed Mar 05, 2014 12:28 pm ] |
| Post subject: | Re: Carbon Fiber rods |
Well, carbon fiber in any form is pretty strong. I'd say using an old arrow for a truss rod is pretty good recycling. Let us know how it turns out. |
|
| Author: | WudWerkr [ Wed Mar 05, 2014 5:14 pm ] |
| Post subject: | Re: Carbon Fiber rods |
Bound to be stronger than it is now . I always use square myself but dont see any reason it wouldnt work round. I agree with Chris , Let us know how it goes . |
|
| Author: | nyazzip [ Thu Mar 06, 2014 9:02 am ] |
| Post subject: | Re: Carbon Fiber rods |
the rods used in guitar making are solid; i'm assuming the arrows are hollow, with very thin walls. strong enough for an arrow, but...... |
|
| Author: | WudWerkr [ Thu Mar 06, 2014 8:50 pm ] |
| Post subject: | Re: Carbon Fiber rods |
nyazzip wrote: the rods used in guitar making are solid; i'm assuming the arrows are hollow, with very thin walls. strong enough for an arrow, but...... Good point , that could make a difference . You can buy the stuff fairly cheap to btw . I use http://www.dragonplate.com/ |
|
| Author: | flounder [ Mon Mar 10, 2014 1:20 pm ] |
| Post subject: | Re: Carbon Fiber rods |
Buying carbon bar of an appropriate size is tricky in the UK but I have bought some square bars, one with a 6mm OD and a 4mm ID, the second with a 4mm OD and a 2.5 mm ID. The smaller rod is a nice fit inside the larger one and my intention was to glue the two together to make a nice strong truss rod. What would be the best glue to bond the two together? Can I use thin CA and wick it down or do I need to use an epoxy glue and hope I don't scrape it all off when I slide it in? |
|
| Author: | Chris Pile [ Mon Mar 10, 2014 4:48 pm ] |
| Post subject: | Re: Carbon Fiber rods |
I would think either will work. CA isn't very shock resistant, but that shouldn't be a problem buried in the neck. Epoxy is relatively stable, although it might creep under high heat - but again shouldn't be a problem. I am pretty interested to see how this works for you. I like the idea of re-purposing broken stuff in unusual ways. |
|
| Author: | frwilliams [ Mon Mar 17, 2014 5:42 pm ] |
| Post subject: | Re: Carbon Fiber rods |
I have not yet used the arrow, but it is solid as opposed to hollow. Still thinkin on it. thx for replies |
|
| Author: | Chris Pile [ Mon Mar 17, 2014 6:49 pm ] |
| Post subject: | Re: Carbon Fiber rods |
What's the holdup? Go for it. |
|
| Author: | nyazzip [ Mon Mar 17, 2014 9:59 pm ] |
| Post subject: | Re: Carbon Fiber rods |
Quote: I have not yet used the arrow, but it is solid as opposed to hollow. must be very expensive/heavy arrows. i think the solid ones are used for bowfishing |
|
| Author: | WudWerkr [ Tue Mar 18, 2014 4:28 pm ] |
| Post subject: | Re: Carbon Fiber rods |
I have used Gorilla glue to put in several and it seems to work well . The one thing I found that helps is to lightly sand the carbon ruffing it a bit and it sticks better |
|
| Author: | wrstew [ Mon Jul 21, 2014 9:08 pm ] |
| Post subject: | Re: Carbon Fiber rods |
If anyone is looking for inexpensive carbon fiber, in the past, walmart locally as well as the box sporting goods stores sell solid cf arrows for children. Have cut into them, and they are completely solid. Great price and no shipping. |
|
| Author: | Jfurry [ Tue Jul 22, 2014 1:09 am ] |
| Post subject: | Re: Carbon Fiber rods |
Make sure there's no rattle before putting the fingerboard back on |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|