| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Ukulele End Graft? http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10128&t=51371 |
Page 1 of 1 |
| Author: | Steve-atl [ Tue Dec 25, 2018 2:17 pm ] |
| Post subject: | Ukulele End Graft? |
Happy Holidays I am building a StewMac Baritone Ukulele kit. I really don’t like my side seam on the back of the ukulele. I mocked up a back section (thank god) and tried to cut an end graft by hand. It didn’t turn out that well. How do you all cut your end grafts? Do you use a router template? Can you buy these or do you make them yourself? Did you build a jig? Any information would be appreciated Thanks |
|
| Author: | Tim Mullin [ Tue Dec 25, 2018 3:12 pm ] |
| Post subject: | Re: Ukulele End Graft? |
Hi Steve, I usually do a simple wedge. Pics tell the story. The wood block is sitting on a folded piece of sandpaper, lined up on guide marks and held with one hand while drawing Japanese pull saw with the other. Clean it out with a chisel, epoxy a wedge and proceed with cutting binding channels.      Sent from my iPad using Tapatalk |
|
| Author: | Allen McFarlen [ Tue Dec 25, 2018 3:13 pm ] |
| Post subject: | Re: Ukulele End Graft? |
I use a template to cut the end graft in the instrument. Both the template and endgraft are cut on my laser. Over the top for your first instrument but it's very quick and accurate. Here's a video I did about a year ago. Not the greatest quality, but you get the idea. |
|
| Author: | Steve-atl [ Wed Dec 26, 2018 10:54 am ] |
| Post subject: | Re: Ukulele End Graft? |
Thanks for your advice My second attempt on my mockup worked a lot better. How do you brace the ukulele when chiseling out the graft? It took a fair amount of clamp pressure to keep the board still while I was doing this. The second problem that I didn’t think out very well. The top and back are already glued on so if I add a graft now the end grains will show. |
|
| Author: | Tim Mullin [ Wed Dec 26, 2018 11:39 am ] |
| Post subject: | Ukulele End Graft? |
Steve-atl wrote: How do you brace the ukulele when chiseling out the graft? It took a fair amount of clamp pressure to keep the board still while I was doing this. My example was actually with a guitar, but I would handle a uke the same way. In my case, I put a cam clamp on either side of the body, with additional clamps holding those to my bench. In Allen’s video, he’s using a custom vice arrangement. Not much pressure is required for either system, provided your chisel is sharp. No need for a mallet! Steve-atl wrote: The second problem that I didn’t think out very well. The top and back are already glued on so if I add a graft now the end grains will show. Well, you have indeed increased your level of difficulty. You could presumably scribe the outer edge with a sharp xacto knife, chisel out carefully, then fit your inlay into the cavity. Personally, I would find it easier and better looking to bind the top and bottom (like in my photos — you can skip the purfling). Might be worth learning this valuable skill on this kit project. Sent from my iPad using Tapatalk |
|
| Author: | Steve-atl [ Wed Dec 26, 2018 12:49 pm ] |
| Post subject: | Re: Ukulele End Graft? |
Your work is beautiful by the way Steve-atl wrote: The second problem that I didn’t think out very well. The top and back are already glued on so if I add a graft now the end grains will show. Well, you have indeed increased your level of difficulty. You could presumably scribe the outer edge with a sharp xacto knife, chisel out carefully, then fit your inlay into the cavity. Personally, I would find it easier and better looking to bind the top and bottom (like in my photos — you can skip the purfling). Might be worth learning this valuable skill on this kit project. Sent from my iPad using Tapatalk[/quote] I was going to bind it but someone said the lining was thin (see photo) and it might make it tricky to rout and install. What do you think? It's a Stewmac kit, I am using the materials they sent |
|
| Author: | Pmaj7 [ Wed Dec 26, 2018 2:04 pm ] |
| Post subject: | Re: Ukulele End Graft? |
You could do binding, but I wouldn't recommend purfling. Keep the binding at about .06" New username, same Pat Mac |
|
| Author: | BradHall [ Wed Dec 26, 2018 2:35 pm ] |
| Post subject: | Re: Ukulele End Graft? |
I just completed my first ukulele, also a Stewmac tenor kit. I didn't like the laminated back edge showing at the sides, so I bound both top and back. Figured why not personalize it a bit so I added a headplate and open gear tuners. Attachment: IMG_1467.jpg Attachment: IMG_1468.jpg Sent from my iPad using Tapatalk |
|
| Author: | Steve-atl [ Wed Dec 26, 2018 4:24 pm ] |
| Post subject: | Re: Ukulele End Graft? |
Brad That looks great. What binding did you use |
|
| Author: | BradHall [ Wed Dec 26, 2018 10:00 pm ] |
| Post subject: | Re: Ukulele End Graft? |
I'm guessing it was some flamed maple, although there is not much flame to speak of. I've got a boneyard tube with odds and ends and the four pieces were long enough to work on a ukulele. One caution; I had no idea a veneer could be as thin as the mahogany laminated back and sides are. Maybe about as thick a quarter of a sheet of standard printer paper. Be very cautious sanding, scraping, or removing masking tape. |
|
| Author: | Steve-atl [ Thu Dec 27, 2018 7:12 am ] |
| Post subject: | Re: Ukulele End Graft? |
BradHall wrote: I've got a boneyard tube with odds and ends and the four pieces were long enough to work on a ukulele. Where did you get it from? One caution; I had no idea a veneer could be as thin as the mahogany laminated back and sides are. Maybe about as thick a quarter of a sheet of standard printer paper. Be very cautious sanding, scraping, or removing masking tape. I have unfortunately found this out already Thanks |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|