Official Luthiers Forum!
http://w-ww.luthiersforum.com/forum/

Loosening a tenor top
http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10128&t=52961		 Page 1 of 1
Author:  bcombs510 [ Sat Feb 22, 2020 10:46 am ]
Post subject:  Loosening a tenor top
Hello,

Looking for some guidance from the experts. :)

I just closed the box on a tenor uke. Tapping the plate beforehand it sounded good, but now that the box it closed it sounds very tight.

I let the two horizontal braces into the lining, solid lining made of paulownia. The fans taper to nothing. I put a 2mm spruce bridge plate in it.

With a guitar I would be reaching in there and solving the problem. That ain’t happening with a uke soundhole. :)

Anyone have creative ideas what to do? I’ll sand the lower bout around the rim to try to loosen it. Any other thoughts? Maybe lighter bridge or heavier bridge?

Brad


Sent from my iPhone using Tapatalk Pro
Author:  dofthesea [ Wed Feb 26, 2020 11:02 am ]
Post subject:  Re: Loosening a tenor top
Whats the top thickness?
Author:  bcombs510 [ Wed Feb 26, 2020 12:14 pm ]
Post subject:  Re: Loosening a tenor top
dofthesea wrote:
Whats the top thickness?


It’s right at 2mm now. I haven’t gotten back to it yet to try to thin around the the rim.

One thing I did differently this time is I put somewhat wide 2mm spruce bridge patch on it. TBH, I don’t know why I made it so wide:

Image

Brad


Sent from my iPhone using Tapatalk Pro
Author:  bcombs510 [ Wed Feb 26, 2020 12:16 pm ]
Post subject:  Re: Loosening a tenor top
Note: The braces we’re tapered and re-peaked after this pic, they are tapered 3-4 mm shorter at the scalloped end and peaked again.


Sent from my iPhone using Tapatalk Pro
Author:  Pmaj7 [ Wed Feb 26, 2020 7:30 pm ]
Post subject:  Re: Loosening a tenor top
Is there a binding on it? Fretboard? Taking the top off isn't too big of a deal. especially if you're going to put binding on later.

Sent from my SM-N960U1 using Tapatalk
Author:  bcombs510 [ Wed Feb 26, 2020 7:53 pm ]
Post subject:  Re: Loosening a tenor top
Just closed the box, no binding or even binding channels cut yet.

I’m may end up taking the top off. Going to sand a bit and see if it somehow works a miracle. :)


Sent from my iPhone using Tapatalk Pro
Author:  unkabob [ Thu Mar 19, 2020 9:28 am ]
Post subject:  Re: Loosening a tenor top
If you have the Hana Lima book, sanding the outer inch and a half should loosen up the top. This is most effective around the lower bout. You may find something on the
Hana Lima website.

Unkabob
Author:  dofthesea [ Mon Mar 23, 2020 11:43 am ]
Post subject:  Re: Loosening a tenor top
Can you give us a picture of the edge profile of top?
Author:  bcombs510 [ Fri Apr 17, 2020 11:14 am ]
Post subject:  Re: Loosening a tenor top
dofthesea wrote:
Can you give us a picture of the edge profile of top?


Crud, I just saw this and I’ve already put binding on. It’s actually almost done, so we will find out soon how much I helped. ;)

Brad


Sent from my iPhone using Tapatalk Pro
Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/