StevenWheeler wrote:
I might as well join the maddness. No idea what it will be yet, but I promise not to a big cheater like Wud.
Heyyyyyyyyyyyyyy Im not Big ! LOLOL ....... um yeah i am
| Official Luthiers Forum! http://w-ww.luthiersforum.com/forum/ |
|
| Steve Wheeler's Challenge Build http://w-ww.luthiersforum.com/forum/viewtopic.php?f=10133&t=37324 |
Page 1 of 6 |
| Author: | StevenWheeler [ Wed Aug 01, 2012 6:20 pm ] |
| Post subject: | Steve Wheeler's Challenge Build |
I might as well join the maddness. No idea what it will be yet, but I promise not to a big cheater like Wud. |
|
| Author: | WudWerkr [ Wed Aug 01, 2012 7:08 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
StevenWheeler wrote: I might as well join the maddness. No idea what it will be yet, but I promise not to a big cheater like Wud. Heyyyyyyyyyyyyyy Im not Big ! LOLOL ....... um yeah i am
|
|
| Author: | StevenWheeler [ Mon Aug 06, 2012 6:43 am ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
O.K. I guess just for fun I'm going to see how many stringed things I can build for $150. I know I can get three, maybe more, we'll see what happens. Steve |
|
| Author: | StevenWheeler [ Wed Aug 08, 2012 9:12 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
First up will be a Pickin' Stick. Forum member JRessler wrote this book just so he could see how little he could earn per hour. It's an even lower pay scale than guitar building, somewhere down near prison labor. It's a pretty simple insturment, three strings tuned to an open cord (G) with a diatonic scale. If you count the frets you'll find an F# thrown in for fun. Attachment: Challange Stick 001.JPG For the materials I went through my pile of leftovers. The wood for the neck is the scrap from a 5/4" Jatoba top for the lower section of a hutch I built. The top is Douglas Fir that first served as a 6x6 post holding up a front porch. The back is going to be a piece of Birdseye Maple that is left over from my TDPRI challenge telecaster. The twig is some sort of rosewood cut from a chunk I got from a friend. It will be used for the saddle and nut. Attachment: Challange Stick 002.JPG These tuners are from the strip down of an old Teisco or something. This was a six on a side set, the other three are on another "Stick". Attachment: Challange Stick 003.JPG
|
|
| Author: | Bryan Bear [ Wed Aug 08, 2012 10:21 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
I can tell this is going to be a fun thread! At the end you should post a video of all of the instruments played at once. |
|
| Author: | WudWerkr [ Thu Aug 09, 2012 8:03 am ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
I have Johns Book and its a nice addition to any Luthiers collection . I picked it up for my daughter to make her first build . I reccomend this book to any newbie that has intrest and needs to hone skill ! |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 8:10 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
That's right Filippo, here at Wheeler Guitars "We spare no Costa"...um, is that already taken? Yes Bryan there will be a pay per veiw concert at the completion of my build(s). My main concern is having enough room left in the budget after this build for the Timpani. |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 8:23 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
It's amazing what you can accomplish in a couple of hours. Simple insturment and easy to build. Here are the major parts milled to size with some layout lines. |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 8:30 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Drill press action. Tuner shaft holes first. Attachment: Challange Stick 004.JPG Attachment: Challange Stick 005.JPG 1/2" bit to clear waste from the headstock slot. Attachment: Challange Stick 006.JPG 5/8" hole to terminate the wishbone. Attachment: Challange Stick 008.JPG
|
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 8:37 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Used the table saw to cut 1/8"x1/8" notches for the nut and at the end of the fretboard. Then 1/8" is removed from the "body" so the top of the sound board is level with the fret board. |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 8:46 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Fun with the small band saw and the edge sander. |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 8:49 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Headstock shaping. |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 9:14 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Time for frets already? This hunk 'o steel ground flat with 100 grit PSA sandpaper stuck on makes neck and fret board leveling easy. Attachment: Challange Stick 026.JPG I use WFret for any odd scale lengths. A razor knife and machinists square mark the fret locations. Attachment: Challange Stick 022.JPG Cutting fret slots is easy when you only do 1/2 the slots in 1/2 a fretboard. Attachment: Challange Stick 024.JPG Hammer Time. Attachment: Challange Stick 027.JPG
|
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 9:29 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Back to my new favorite tool, the edge sander. I've always wanted to try dressing fret ends in this manner but haven't had the opportunity until I got this machine. I bet it didn't take 12 seconds total to get all the fret ends flush and beveled. I'll get a better pic of the ends tomorrow. |
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 9:47 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Now here is a handsome group of photos. First, an out of focus shot of cutting the waste from the wishbone. Attachment: Challange Stick 031.JPG A nice close up of finishing the cut on the bandsaw. Maybe getting a bit more bandsaw blade in the shot would help. Attachment: Challange Stick 032.JPG More focus problems. Attachment: Challange Stick 033.JPG Best for last. Fabulous shot of sawdust artfully framed by an end block freshly clamped in place. Attachment: Challange Stick 034.JPG
|
|
| Author: | StevenWheeler [ Thu Aug 09, 2012 9:51 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Finished up the head stock shaping with a rasp and some files. |
|
| Author: | DennisK [ Thu Aug 09, 2012 10:05 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
You're really cranking on this thing  Looks like a lot of fun.I need to try designing and building some super simple instruments like this. |
|
| Author: | Tony_in_NYC [ Fri Aug 10, 2012 12:53 am ] |
| Post subject: | Steve Wheeler's Challenge Build |
When you say "spare no Costa" are you suggesting that you kill my family members? Because at Costa guitars, we don't know who you are or what you want, but I can tell you this: if you're looking for ransom, I have tons of money but I won't pay you. What I also have are a very particular set of skills. Skills honed over a lifetime of being sarcastic. Skills that make me a nightmare for people like you. If you stop the Costa jokes now I will forget this ever happened. But if you don't, I will hunt you down, I will find you and I will post a goat pic in your challenge thread that gets it shut down. |
|
| Author: | StevenWheeler [ Fri Aug 10, 2012 7:00 am ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Tony_in_NYC wrote: When you say "spare no Costa" are you suggesting that you kill my family members? Because at Costa guitars, we don't know who you are or what you want, but I can tell you this: if you're looking for ransom, I have tons of money but I won't pay you. What I also have are a very particular set of skills. Skills honed over a lifetime of being sarcastic. Skills that make me a nightmare for people like you. If you stop the Costa jokes now I will forget this ever happened. But if you don't, I will hunt you down, I will find you and I will post a goat pic in your challenge thread that gets it shut down. Good luck. Oh and Tony, get some rest. You look tired. |
|
| Author: | Tony_in_NYC [ Fri Aug 10, 2012 7:19 am ] |
| Post subject: | Steve Wheeler's Challenge Build |
I am. My two year old broke his leg on Tuesday so he has not been sleeping very much. As a result neither have the wife and I. But I think my "Taken" reference was pretty good despite my lack of sleep. You have to give me credit for that. |
|
| Author: | StevenWheeler [ Fri Aug 10, 2012 12:57 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
A couple of free hours this morning so I thought I'd finish this one. Shaped the neck with a 1/2" roundover bit. Attachment: Challange Stick 001.JPG Cut the ends of the sides flush to the tail block. Attachment: Challange Stick 002.JPG Back to the hunk o' steel to true up the gluing surfaces. Attachment: Challange Stick 003.JPG
|
|
| Author: | StevenWheeler [ Fri Aug 10, 2012 1:07 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Some back and top prep. |
|
| Author: | StevenWheeler [ Fri Aug 10, 2012 1:09 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Glue the back. Attachment: Challange Stick 009.JPG Then the top. Attachment: Challange Stick 010.JPG Made a nut while the glue dried. Attachment: Challange Stick 012.JPG
|
|
| Author: | StevenWheeler [ Fri Aug 10, 2012 1:13 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Some trimming and shaping. Attachment: Challange Stick 013.JPG Attachment: Challange Stick 015.JPG The two end tuners need new string holes drilled. I drill the countersink first to keep the 5/64" bit from falling off the post. |
|
| Author: | StevenWheeler [ Fri Aug 10, 2012 1:20 pm ] |
| Post subject: | Re: Steve Wheeler's Challenge Build |
Installed 3 4d trim nails to hook the strings then strung it up and glued the saddle in place. Attachment: Challange Stick 019.JPG Attachment: Challange Stick 020.JPG All done save for finish sanding and satin polyurethane. I think maybe I'll install the third fret also. A bit dificult to play a C without it. |
|
| Page 1 of 6 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|