Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Tue Dec 10, 2024 10:06 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Pinless Bridge Placement
PostPosted: Mon Jun 16, 2014 9:58 pm 
Offline
Walnut
Walnut

Joined: Mon Jun 16, 2014 9:30 pm
Posts: 1
First name: Steve
Last Name: Bernhardt
Focus: Repair
Status: Semi-pro
I have a Takamine GS330S with a bridge that needs to be re-glued. It came to me with a replacement fit bridge ordered form AllParts. This model has a pinless style bridge.

I have watched lots of videos and read books/articles about gluing bridges, and I have noticed that people will often use the two E hole pins for realignment.

How can I re-align a bridge that has no pins? Has anyone ever replaced one of these? Some guidance would be much appreciated.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Sat Jun 21, 2014 9:48 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun May 16, 2010 10:02 am
Posts: 89
First name: michael
Last Name: jennings
City: Lopez Island
State: WA
Zip/Postal Code: 98261
Country: United States
Focus: Repair
Status: Semi-pro
I use several layers of masking tape to establish the front edge, and the ends [side to side]. Then careful clamping.

MJ


Top
 Profile  
 
PostPosted: Sat Jun 21, 2014 11:37 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 12, 2005 5:46 am
Posts: 2969
Location: United States
A couple of small (1/16 or less) locating holes at each end of the saddle slot will do the trick. Use the shank of the drill bit as the pin, be sure to apply some wax to it for easy removal.

_________________
Jim Watts
http://jameswattsguitars.com


Top
 Profile  
 
PostPosted: Tue Oct 28, 2014 7:43 am 
Offline
Walnut
Walnut

Joined: Mon Oct 06, 2014 4:52 pm
Posts: 14
First name: Sparky
Last Name: Weintraut
City: Blacksburg
State: Virginia
Zip/Postal Code: 24060
Country: USA
Focus: Build
Status: Amateur
I second Jim's process. I use the same with classical bridges, and just use toothpicks as my pins/plugs.


Top
 Profile  
 
PostPosted: Tue Oct 28, 2014 1:47 pm 
Offline
Koa
Koa

Joined: Sun Apr 25, 2010 4:46 pm
Posts: 527
First name: Mark
Last Name: McLean
City: Sydney
State: New South Wales
Zip/Postal Code: 2145
Country: Australia
Focus: Build
Status: Amateur
+1 for the locating holes within the saddle slot.
I hadn't thought to wax the pins to make them easy to remove - and easier to slide the bridge on to them. Thanks for the tip Jim.


Top
 Profile  
 
PostPosted: Tue Nov 04, 2014 12:02 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue May 13, 2008 10:44 am
Posts: 6256
Location: Virginia
I just use masking tape as well. If you use HHG or high tack fish glue then you will not have to worry so much about slippage when clamping. The tape will help with that if you use Titebond but just be careful.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com