Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Nov 22, 2024 8:15 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 16 posts ] 
Author Message
PostPosted: Tue Jan 16, 2024 12:41 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2519
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
I have a question but didn't want to hijack Brad's thread about binding blow outs when routing the mortise in the neck block. I guess this may be a general question about different work flows. The builder I learned from routed the mortise in the neck block before gluing it to the sides. That's how I've done it ever since. I use bolt-on necks with a tenon. When it comes time to open the mortise, I use a pull saw to cut a small opening in the sides covering the mortise at the top of the mortise. The opening is big enough to fit a flush trim bit into the mortise and then I free hand rout the opening. This approach has always worked for me with no mishaps (so far).

So, is there an advantage to routing the mortise in the fully assembled body either functionally or as part of a work flow? I like to learn about approaches other people use so I'm wondering. Thanks.

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post: bcombs510 (Tue Jan 16, 2024 8:52 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 1:22 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7377
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
To me, it has always made sense to base your angles from actual reality rather than predicted idealization. It’s so easy to miss by a smidge but also so easy to account for it…

Any advantage/disadvantage will stem out from workflow. Either/or works if you accommodate in process.



These users thanked the author meddlingfool for the post (total 2): bcombs510 (Tue Jan 16, 2024 8:52 am) • J De Rocher (Tue Jan 16, 2024 1:55 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 7:55 am 
Offline
Koa
Koa
User avatar

Joined: Sun Jun 22, 2014 1:45 pm
Posts: 1483
First name: Michael
Last Name: Colbert
City: Anacortes
State: WA
Focus: Build
Hi Jay,

You’ve seen my approach before. I make neck blocks 10 at a time on my CNC. The same block fits everything from my “0” to my 28” multi-scale baritone, exact same block. After radiusing to match the body profile I clamp my well squared neck block to my bench top and glue on the rims - (no, I do not glue the blocks in in the mold) this ensures that everything remains perpendicular to the bench surface. Once the neck and tail block are glued in, I return the assembly to the mold/form and cut a 40’ radius on the top side using my powered dish sander. Then the top linings go in - back to the dish sander. Popsicle stick brace and upper transverse - back to the dish sander. The assembly gets checked for proper alignment throughout the process using a clear acrylic template and is finally placed on a 40’ radius assembly board where the braced top gets glued to the rims.

I know it’s different, but it’s what I’ve come up with over the years.

Cheers, M


You do not have the required permissions to view the files attached to this post.



These users thanked the author Michaeldc for the post (total 3): Pmaj7 (Thu Jan 18, 2024 10:11 pm) • J De Rocher (Tue Jan 16, 2024 11:59 am) • bcombs510 (Tue Jan 16, 2024 8:51 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 8:09 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Dec 17, 2013 10:52 pm
Posts: 3070
First name: Don
Last Name: Parker
City: Charleston
State: West Virginia
Zip/Postal Code: 25314
Country: USA
Focus: Build
Status: Amateur
I’ve cut the mortise in the block before assembly, and I’ve cut it after the whole body is glued together, including binding and purfling. I currently do the latter. Both work fine, but I prefer cutting the mortise later and creating good alignment in the completed box, rather than cutting the mortise earlier and trying to maintain good alignment as the box is constructed. Just my personal preference.



These users thanked the author doncaparker for the post (total 2): J De Rocher (Tue Jan 16, 2024 11:59 am) • bcombs510 (Tue Jan 16, 2024 8:51 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 8:49 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7375
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
I've done dovetails and bolt-on mortices in block before assembly and they worked out but like Don, I cut them after the box is built now. Of course I am also bending my sides by hand so each box is a bit different and my tolerances are not as tight as some others, especially those using CNCs.

_________________
Steve Smith
"Music is what feelings sound like"



These users thanked the author SteveSmith for the post (total 2): J De Rocher (Tue Jan 16, 2024 12:00 pm) • bcombs510 (Tue Jan 16, 2024 8:51 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 8:56 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3594
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Michaeldc wrote:
I clamp my well squared neck block to my bench top and glue on the rims - (no, I do not glue the blocks in in the mold) this ensures that everything remains perpendicular to the bench surface.


I need to move in this direction vs screwing through the mold into the block. There is still opportunity for things to squirm a bit, even with the screw, if you don’t have full height mold / cauls. Clamping the block to a flat surface just makes sense.


Sent from my iPhone using Tapatalk Pro

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars



These users thanked the author bcombs510 for the post: Michaeldc (Tue Jan 16, 2024 9:01 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 9:04 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7375
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
bcombs510 wrote:
Michaeldc wrote:
I clamp my well squared neck block to my bench top and glue on the rims - (no, I do not glue the blocks in in the mold) this ensures that everything remains perpendicular to the bench surface.


I need to move in this direction vs screwing through the mold into the block. There is still opportunity for things to squirm a bit, even with the screw, if you don’t have full height mold / cauls. Clamping the block to a flat surface just makes sense.


I like that idea. I've been screwing the blocks into the mold but that is a bit of a PITA. Maybe I can rig up a method to clamp the blocks down and use the mold too when I glue the blocks to the sides. Hmm....

_________________
Steve Smith
"Music is what feelings sound like"



These users thanked the author SteveSmith for the post (total 2): Michaeldc (Tue Jan 16, 2024 10:20 am) • bcombs510 (Tue Jan 16, 2024 10:12 am)
Top
 Profile  
 
PostPosted: Tue Jan 16, 2024 11:33 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4805
I used pre-carved necks on my first few guitars. They came as a neck/end block combo. I always worried about getting them glued in just right so that the mortis was in line with the centerline of the guitar. I personally find it easier to rout the mortis once the block is glued in.

Brad and Steve, I’m not quite sure I understand what you mean about screwing the blocks into the mold?


Sent from my iPhone using Tapatalk



These users thanked the author James Orr for the post: bcombs510 (Wed Jan 17, 2024 1:38 am)
Top
 Profile  
 
PostPosted: Wed Jan 17, 2024 12:00 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Dec 17, 2013 10:52 pm
Posts: 3070
First name: Don
Last Name: Parker
City: Charleston
State: West Virginia
Zip/Postal Code: 25314
Country: USA
Focus: Build
Status: Amateur
James—

I use screws, too. This is a John Hall idea. During body construction, instead of using a head to tail spreader to keep the head block and tail block flush to the mold, you drive screws through the mold from the outside and into the blocks. I use two screws per block (spread vertically), and that works well for me. Since that’s how you keep the blocks where they should be, it is a natural step to want to glue the blocks to the sides using the screws. But, as you have heard, that can be hard to do well and get a good glue joint. Some folks get better results by gluing the blocks to the sides away from the mold.



These users thanked the author doncaparker for the post: bcombs510 (Wed Jan 17, 2024 1:38 am)
Top
 Profile  
 
PostPosted: Wed Jan 17, 2024 6:03 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Dec 14, 2007 3:21 pm
Posts: 3388
Location: Alexandria MN
I started out cutting the mortise first but later went to doing it after the box was assembled. Both ways worked. I think I changed thinking the centering would be more accurate but quite honestly I don’t remember any big issues doing it first. Well except one where I opened the mortise before cutting the binding. Whoops, nice scallop right on the centerline of the back.

_________________
It's not what you don't know that hurts you, it's what you do know that's wrong.


Top
 Profile  
 
PostPosted: Wed Jan 17, 2024 7:29 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4805
doncaparker wrote:
James—

I use screws, too. This is a John Hall idea. During body construction, instead of using a head to tail spreader to keep the head block and tail block flush to the mold, you drive screws through the mold from the outside and into the blocks. I use two screws per block (spread vertically), and that works well for me. Since that’s how you keep the blocks where they should be, it is a natural step to want to glue the blocks to the sides using the screws. But, as you have heard, that can be hard to do well and get a good glue joint. Some folks get better results by gluing the blocks to the sides away from the mold.

Very interesting. I’ve always used F-clamps to clamp them from outside of the mold, into (or against) the mold. Where the sides are proud of the mold, I use a caul to protect the sides from clamp marks.

Image




Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Thu Jan 18, 2024 12:16 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sun Jun 02, 2013 8:16 am
Posts: 485
First name: Brian
City: U.P.
State: Michigan
Focus: Build
I guess the reality in my shop is that every step in building is a compromise, in this case between the perfection I want to happen and what happens in real life. Sometimes individually they don't show to the eye but cumulatively they might be enough to wish for a little correction.

Making the neck mortise happen when the box is closed and bound gives me one last chance to adjust position to make slight corrections and have everything line up. Neck, top seam, sound hole, butt wedge -- all that stuff.

_________________
Brian R, Wood Mechanic
N8ZED


Top
 Profile  
 
PostPosted: Thu Jan 18, 2024 3:42 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7375
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
For me the screws in the blocks are to maintain block alignment in the jig and to eliminate the need for a neck block-to-tail block spreader when gluing the back and top. I still also use clamps when gluing the sides to the blocks.

_________________
Steve Smith
"Music is what feelings sound like"



These users thanked the author SteveSmith for the post: bcombs510 (Thu Jan 18, 2024 4:41 pm)
Top
 Profile  
 
PostPosted: Thu Jan 18, 2024 4:45 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3594
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Yeah, I was going to mention this too.. the possible rotation of the neck block when gluing the plates is the real way to hose up the neck geometry real quick.

I like the idea Don had of two screws vertically oriented.

I’ve been toying with the idea of pulling a square of vacuum through the mold as well, could be an interesting way to do it from the outside without having any holes.

Some context: I don’t always want to put an end wedge in so the holes there are problematic in some cases. Ex:

Image

Spreaders are the logical answer but what’s the fun in that?


Sent from my iPhone using Tapatalk Pro

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Thu Jan 18, 2024 6:28 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7375
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
The longwise spreader I had wasn’t very good, I’ve thought about making a better one. Then I could just use a couple of 1/8” dowel pins to index the neck block in place. I don’t see a need to index the tail block in position if I have a decent spreader to hold it in place while I glue the top and back on.

_________________
Steve Smith
"Music is what feelings sound like"



These users thanked the author SteveSmith for the post: bcombs510 (Thu Jan 18, 2024 6:45 pm)
Top
 Profile  
 
PostPosted: Fri Jan 19, 2024 5:35 pm 
Offline
Koa
Koa
User avatar

Joined: Wed Jan 24, 2007 2:45 pm
Posts: 1336
Location: Calgary, Canada
Status: Amateur
I drill the holes for the bolt on neck (I use hanger bolts) and truss rod after the block is glued to the sides but before glueing the back and sides on. Easy for me on the drillpress. I have a Simpson Jig I bought at a swapapalooza way back when so still use it for setting the neck angle and routing the mortise and tenon. Transfer punches make it easy for me to mark the hanger bolt locations on the neck tenon. Nowhere near as elegant as some of the methods on this thread but works well for this luddite.



These users thanked the author Darrel Friesen for the post: bcombs510 (Fri Jan 19, 2024 7:19 pm)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: CarlD and 52 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com