***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Tue Nov 26, 2024 6:11 pm


Board index » Forum Archive

All times are UTC - 5 hours





Post new topic Reply to topic  Page 1 of 2
  [ 34 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
FishtownMike
 Post subject:
PostPosted: Fri Nov 23, 2007 3:50 pm 
Offline
Koa
Koa

Joined: Sat Aug 04, 2007 10:37 am
Posts: 590
Location: United States
First name: Michael
Last Name: Shaw
City: Phila
State: PA
Zip/Postal Code: 19125
Country: United States
When it comes to jointing tops and backs what do you use? Hand plane and a shooting board or a jointer. I'm thinking of buying a delta 6" benchtop jointer. I was just wondering if i really need it.

_________________
Guitars, guitars and more guitars.
Top
 Profile  
 
Steve Saville
 Post subject:
PostPosted: Fri Nov 23, 2007 3:55 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Nov 26, 2005 7:32 pm
Posts: 1969
Location: United States
Shooting board and a hand plane works great. For real difficult tops, I also use a 36" long straight extruded aluminum square with sandpaper attached to it. I use that to get it close, but I always follow up with the hand plane because I want to join planed, not sanded surfaces.

_________________
"An adventure is only an inconvenience rightly considered. An inconvenience is an adventure wrongly considered." G. K. Chesterton.
Top
 Profile  
 
Rick Turner
 Post subject:
PostPosted: Fri Nov 23, 2007 4:30 pm 
Offline
Koa
Koa

Joined: Wed Aug 24, 2005 11:13 am
Posts: 1398
Location: United States
A finely tuned ancient Delta 6" jointer with sharp knives and then hot hide glue.   Invisible glue lines...   

You do have to develop a touch with a jointer just as with any other tool.   Where you apply the pressure, how you shift the pressure, when to back off...it's all important for tight joints.

What I never understood was why some power tool company hasn't come out with a true glue edge jointer...something like a large diameter head, four knife shaper with a proper jointer fence arrangement.   It wouldn't need to have a very tall cutter head...just enough for the average glue line width.   It would be much easier to handle top, backs, and a lot of the other kinds of pieces that get edge glued with a shaper table as a reference. Might just have to build one out of a shaper some day.
Top
 Profile  
 
Chas Freeborn
 Post subject:
PostPosted: Fri Nov 23, 2007 4:44 pm 
Offline
Koa
Koa

Joined: Tue Mar 01, 2005 3:00 pm
Posts: 656
Location: United States
Focus: Build
Status: Professional
I use my Shop Fox 8" four knife head jointer. What Rick said about finesse.
My 1980 something Rockwell 2 hp shaper came with a fence that has
independently adjustable fence halves to allow for use as a joitnting
machine.
If I was runnning a hundred or so tops a month I'd dedicate it for that
purpose with a downshear spiral cutter. As it is I use it for a couple of neck
making operations, as well as the occasional powerfed millwork run of
moulding for furniture or my house...
Speaking of neck making- Rick- did/do you use your pin router for the
rounding operation? If so, what was the orientation of the stock/cutter/
pattern?

-C

_________________
Freeborn Guitars
and home of BeauGuard©
Top
 Profile  
 
Bob Garrish
 Post subject:
PostPosted: Fri Nov 23, 2007 4:44 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue May 02, 2006 9:02 am
Posts: 2351
Location: Canada
First name: Bob
Last Name: Garrish
City: Toronto
State: Ontario
Country: Canada
Status: Professional
Kevin Ryan uses the Fadal to cut his joints. Guaranteed dead straight line if it's along an axis. I'm sure an analog could be made with a near-zero-runout router of some kind on rails.

I've been using my jointer, it's a General helical head and it makes nice joints. Considering the number of tops I'm about to join, though, I think the Fadal is going to get a new jig...the time savings will add up over 100 tops in one week...

Also, I'm not sure if it was Mario mentioning it last night or a post here where I first heard it, but cut a notch out of the way on one of the plates at each end on the jointed face before joining and it's a lot easier to find the center line.

_________________
Bob Garrish
Former Canonized Purveyor of Fine CNC Luthier Services
Top
 Profile  
 
Brad Way
 Post subject:
PostPosted: Sat Nov 24, 2007 12:37 am 
Offline
Koa
Koa

Joined: Tue Jul 04, 2006 3:24 am
Posts: 744
Location: United States
I have a jointer but wasn't getting a very good joint (It is a Jet and needs some tuning). I tried the shooting board method and was very impressed.

_________________
Brad
Avon, OH
Top
 Profile  
 
jhowell
 Post subject:
PostPosted: Sat Nov 24, 2007 12:56 am 
Offline
Koa
Koa
User avatar

Joined: Wed Mar 29, 2006 11:21 am
Posts: 805
Location: United States
First name: Jim Howell
I use a shooting board and an old Stanley #5 that has Hock steel in it.  Simple, fast and quiet.

_________________
Jim Howell
Charlotte, NC
Top
 Profile  
 
John Mayes
 Post subject:
PostPosted: Sat Nov 24, 2007 1:07 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Sat Jan 08, 2005 3:37 am
Posts: 2670
Location: United States
First name: John
Last Name: Mayes
City: Norman
State: OK
Focus: Build
Status: Professional
I use a #7 Lie Neilsen plane with a shooting board made from phenloic faced plywood, but I used a 6" jointer for years with no problems at all. At McPherson we use a cnc as well. I even used a router table with a special fence I made to replicate a jointer for some time.

_________________
John Mayes
http://www.mayesluthier.com
Top
 Profile  
 
Hesh
 Post subject:
PostPosted: Sat Nov 24, 2007 1:48 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 13387
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
I have been joining plates with just a plane and two boards and some clamps and the results are fine.

The plane is a #5 reconditioned Record from Todd Stock and it works great and still has a great edge on it after many guitars.  This pic should be self explanatory.
Top
 Profile  
 
Glenn LaSalle
 Post subject:
PostPosted: Sat Nov 24, 2007 2:05 am 
Offline
Contributing Member
Contributing Member

Joined: Sat Aug 25, 2007 2:05 am
Posts: 685
Location: Saint Petersburg, Florida
First name: Glenn
Last Name: LaSalle
City: Saint Petersburg
State: Florida
Status: Amateur

I am new to building, but have thought about this quite a bit.  I came to the conclusion that for me, a hobbyist, it made sense to use the shooting board/plane method.  I have a nice Record #5 and recently built my shooting board after studying the OLF archives. The archives are a treasure mine!


Glenn
Top
 Profile  
 
DP LaPlante
 Post subject:
PostPosted: Sat Nov 24, 2007 3:02 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Aug 25, 2007 12:59 pm
Posts: 241

For years I depended on the use of one particular jointer that I had access to for excellent results. Unfortunately that machine was destroyed in an accident during a move and for several years getting good results in joining tops was a problem.


Recently at the Romanillos course in Spain Jose' illustrated the proper use of the shooting board and plane combination as well as the little tricks of pressure and release neccessary to producing a good join.


Upon my return 10 bucks worth of material to make the board and the purchase of an old jointing plane (the big long one made by Stanley for Montgomery Ward) for 50 bucks on EBAY means that I've solved this particular problem.


I think it is an excellent solution for the small builder. Yes, I have a small jointer but to match the quality of the shooting board approach you will need to make a substantial investment in a quality machine. 


  
Top
 Profile  
 
KHageman
 Post subject:
PostPosted: Sat Nov 24, 2007 3:45 am 
Offline
Cocobolo
Cocobolo

Joined: Tue Jan 18, 2005 1:15 pm
Posts: 209
Location: United States
First name: Ken
Last Name: Hageman
City: Statesville
State: NC
Zip/Postal Code: 28625
Focus: Build
Status: Amateur
I like using a shooting board with a 36 inch level. I attach sandpaper along
the solid edge of the level and use it to true the joing. Has worked great for
me.


Top
 Profile  
 
Kent Chasson
 Post subject:
PostPosted: Sat Nov 24, 2007 4:55 am 
Offline
Koa
Koa
User avatar

Joined: Fri Mar 23, 2007 9:56 am
Posts: 1271

The reason for a guitar builder to buy jointer isn't for edge joining but for surface flattening.  Any edge joining in guitar work can easily be done in other ways.  But for flattening neck stock, fingerboards, brace stock or backs (if re-sawing your own), a jointer is the way to go.  And then, once you have it, edge joining is a breeze too.


They do require good set-up though.  The tables have to be co-planer and particularly, the outfeed table needs to be at just the right height.  I find that the outfeed table height is so critical that I can get it perfect for joining rosewood backs and then have to adjust it slightly up for doing softer top wood.


_________________
http://www.chassonguitars.com
Top
 Profile  
 
James Orr
 Post subject:
PostPosted: Sat Nov 24, 2007 5:02 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4805
DP, I'd enjoy a picture or two of your setup if you have them available.

Hesh, you use your straightedge under the stack, right? The gap between
the plane's sidewall and blade ride along it if I remember correctly. That's
the route I've been planning to go.


Top
 Profile  
 
Howard Klepper
 Post subject:
PostPosted: Sat Nov 24, 2007 5:20 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue Jan 25, 2005 6:16 am
Posts: 2692
I hate to hijack, but the basic question has been answered.

Something that has bothered me for years about jointing with a plane:

If a machine jointer has to have the outfeed table flush with the cutter, and the infeed a bit lower to cut a straight jointing surface, then how can a hand plane do it with the "infeed" and "outfeed" in the same plane and the cutter sticking up from that plane? If you set up a machine jointer like that, you would not get a true cut.

_________________
Howard Klepper
http://www.klepperguitars.com

When all else fails, clean the shop.
Top
 Profile  
 
DP LaPlante
 Post subject:
PostPosted: Sat Nov 24, 2007 5:20 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Aug 25, 2007 12:59 pm
Posts: 241
James, here's my set up. The clamps allow me to two hand the plane though Jose' held the top with his left hand and worked the plane with his right. 
Top
 Profile  
 
DP LaPlante
 Post subject:
PostPosted: Sat Nov 24, 2007 5:43 am 
Offline
Cocobolo
Cocobolo

Joined: Sat Aug 25, 2007 12:59 pm
Posts: 241

I think Howard it is that the plane actually works at a slight angle. The surface of the plane behind the blade become the "outfeed" table as you move through the cut. Obviously it's much longer than the front (infeed) surface and keeping steady pressure on the area behind the blade maintains the angle of attack.
Top
 Profile  
 
Bob Garrish
 Post subject:
PostPosted: Sat Nov 24, 2007 6:08 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue May 02, 2006 9:02 am
Posts: 2351
Location: Canada
First name: Bob
Last Name: Garrish
City: Toronto
State: Ontario
Country: Canada
Status: Professional
[QUOTE=Howard Klepper]If a machine jointer has to have the outfeed table flush with the cutter, and the infeed a bit lower to cut a straight jointing surface, then how can a hand plane do it with the "infeed" and "outfeed" in the same plane and the cutter sticking up from that plane? If you set up a machine jointer like that, you would not get a true cut.[/QUOTE]

Ignoring cutters, a jointer is a more advanced machine than a plane. It can do everything a plane can do, but can also move the infeed and outfeed independently of eachother whereas a plane essentially forces them to be coplanar.

If you start with a convex surface, a plane or jointer with both surfaces level with the cutter will cut it to a flat given enough straight line passes. The trick is the linear passes. A jointer, because of the cutterhead being level with the outfeed, forces linear passes after the cut starts and so it continues to work even when the cutter projects past the infeed. A plane doesn't, so it's on you to control that.

You could force a properly setup jointer to make the plane mistake, but you'd have to be very consciously rotating your work and ignoring contact with the outfeed.

_________________
Bob Garrish
Former Canonized Purveyor of Fine CNC Luthier Services
Top
 Profile  
 
Rick Turner
 Post subject:
PostPosted: Sat Nov 24, 2007 6:45 am 
Offline
Koa
Koa

Joined: Wed Aug 24, 2005 11:13 am
Posts: 1398
Location: United States
I used to use a fixture (designed I think by Cumpiano) that had two precision ground steel rails on which a hand jointer plane would ride...the iron was ground narrower at the edge so it missed the rails.   It worked great, but not any better than I can do now in 1/10 the time on my jointer. We are often doing runs of 20 to 30 tops, ditto on backs, and the jointer works great.   Most of my employees touch up the edge on 150 grit self-stick sand paper on my pin router table using a vertical fence, but I don't seem to need to. Too many years using a jointer, I guess...
Top
 Profile  
 
Hesh
 Post subject:
PostPosted: Sat Nov 24, 2007 7:00 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 13387
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
James buddy I used to use a 24" straight edge but after reading over and over again here that it was not necessary I nixed it.  So no more training wheels here.

The trick is to learn how to be very uniform in the pressure with the plane and to keep the sole flat on the edge at all times.

If you use a level with sand paper on it, which I have used too to touch up a joint on the high spots - be sure to use clean paper on the level or dedicate it to only tops or only backs.  Ever see a darker line in finished guitars here or on yours - if the joint was sanded with a level and dirty paper this is likely the cause.
Top
 Profile  
 
Mike Collins
 Post subject:
PostPosted: Sat Nov 24, 2007 7:01 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Mar 06, 2006 10:10 pm
Posts: 2485
Location: Argyle New York
First name: Mike/Mikey/Michael/hey you!
Last Name: Collins
City: Argyle
State: New York
Zip/Postal Code: 12809
Country: U.S.A. /America-yea!!
Focus: Build
Status: Professional
My jointer is fine for most tops & backs.
I used a shooting board & still do once in awhile.
BUT my jointer is set up perfect for just this !

BUT for figured woods I use a router table set up with a pattern making bit with a top bearing.
I joined a 3/8" birch plywood piece on one edge(I run this edge along the bearing)-the piece is big enough to hold a 8" back taped together exactly how I want them.
I just overhang the set enough for the bit to cut it cleanly!
Comes out great every time!
The router runs so fast & I move the jig so slow that there is NO tearout!!
I have lots of highly figured woods and needed to have a sure way to join them.
MIke


www.collinsguitars.com

_________________
Mike Collins
Top
 Profile  
 
Wade Sylvester
 Post subject:
PostPosted: Sat Nov 24, 2007 8:18 am 
Offline
Koa
Koa
User avatar

Joined: Fri Jan 07, 2005 3:21 am
Posts: 684
Location: Nashua, NH
Howard,
I think the work-around with the "infeed" and "outfeed" being in the same plane is also handled by backing in the blade as you shoot your final cuts. The blade is just barely sticking out shaving a very thin slice. This and the slight pressure behind the blade gets the straight cut.

_________________
Wade
Nashua, NH
http://www.wadefx.com
Top
 Profile  
 
FishtownMike
 Post subject:
PostPosted: Sat Nov 24, 2007 8:31 am 
Offline
Koa
Koa

Joined: Sat Aug 04, 2007 10:37 am
Posts: 590
Location: United States
First name: Michael
Last Name: Shaw
City: Phila
State: PA
Zip/Postal Code: 19125
Country: United States
[QUOTE=Howard Klepper] I hate to hijack, but the basic question has been answered.

Something that has bothered me for years about jointing with a plane:

If a machine jointer has to have the outfeed table flush with the cutter, and the infeed a bit lower to cut a straight jointing surface, then how can a hand plane do it with the "infeed" and "outfeed" in the same plane and the cutter sticking up from that plane? If you set up a machine jointer like that, you would not get a true cut.[/QUOTE]
Howard I'm glad you brought this up. I have had this same thought. I like to know the answer to this too.

_________________
Guitars, guitars and more guitars.
Top
 Profile  
 
FishtownMike
 Post subject:
PostPosted: Sat Nov 24, 2007 8:35 am 
Offline
Koa
Koa

Joined: Sat Aug 04, 2007 10:37 am
Posts: 590
Location: United States
First name: Michael
Last Name: Shaw
City: Phila
State: PA
Zip/Postal Code: 19125
Country: United States
[QUOTE=KHageman] I like using a shooting board with a 36 inch level. I attach sandpaper along
the solid edge of the level and use it to true the joing. Has worked great for
me. [/QUOTE]
I think I like the idea of this method the best. If i'm gonna do it by hand. I have seen this method before in wood working magazines.

_________________
Guitars, guitars and more guitars.
Top
 Profile  
 
James Orr
 Post subject:
PostPosted: Sat Nov 24, 2007 8:57 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4805
Thanks, Hesh. You posted a tutorial on the way you like to joint and glue
tops that I bookmarked. I thought the straightedge was pretty innovative
and was looking forward to using mine, haha.

By uniform pressure, do you mean uniform in front and behind of the
iron?

When I was running the school's shop in college, making manipulatives
for the math dept., I joined a few tops and backs on the Delta Unisaw of
all things. High quality blade and a sled. I have a video of it.    

Lots of great ideas in this thread. I like Mike's use of a router.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 34 posts ]  Go to page 1, 2  Next

Board index » Forum Archive

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 27 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com