***** Guitar Project Jigs, Tools & Techniques Online Resources Archives OLF Video Page Library of plans MP3 Library Inlay Class
Offical Luthiers Forum





And our community proudly sponsored by:

RC Tonewoods | Stewart MacDonald | LuthiersForum
TasmanianTonewoods | OLF | OLF MERCH
Luthier Suppliers | Pacific Coast Woods | ELEVATE
OLF X | Tasmanian Acoustic Tonewood | Luthiers Forum Store!
Luthiers Forum | OLF Facebook | AVAIL SPACE
OLF | Alaska Specialty Woods | A.Hix Tonewood
Duke of Pearl | Birkonium CNC | Space




Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Sat Nov 23, 2024 2:14 am


Board index » Forum Archive

All times are UTC - 5 hours





Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 
  Print view Previous topic | Next topic 
Author Message
stan thomison
 Post subject:
PostPosted: Mon Jan 17, 2005 8:36 am 
Offline
Contributing Member
Contributing Member

Joined: Mon Jan 03, 2005 7:46 am
Posts: 1315
Location: Branson, MO
First name: stan
Last Name: thomison
City: branson
State: mo
Zip/Postal Code: 65616
Country: united states
Focus: Build
Status: Professional
How tall are most(or anyone for that matter) making X braces at the lap joint?


Top
 Profile  
 
Steve Kinnaird
 Post subject:
PostPosted: Mon Jan 17, 2005 8:40 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 05, 2005 3:45 pm
Posts: 4337
Location: United States
Around 5/8". This is up for review, though. Thanks for the question, Stan.

_________________
From Nacogdoches...the oldest town in Texas.

http://www.stephenkinnaird.com
Top
 Profile  
 
stan thomison
 Post subject:
PostPosted: Mon Jan 17, 2005 8:55 am 
Offline
Contributing Member
Contributing Member

Joined: Mon Jan 03, 2005 7:46 am
Posts: 1315
Location: Branson, MO
First name: stan
Last Name: thomison
City: branson
State: mo
Zip/Postal Code: 65616
Country: united states
Focus: Build
Status: Professional
Do make them taller or shorter for guitar size, say OM vs Dred, jumbo etc?
Top
 Profile  
 
Steve Kinnaird
 Post subject:
PostPosted: Mon Jan 17, 2005 9:05 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 05, 2005 3:45 pm
Posts: 4337
Location: United States
Yes, a bit--but mainly thinner, as needed. I also scallop pretty much like the Martin blueprint.

_________________
From Nacogdoches...the oldest town in Texas.

http://www.stephenkinnaird.com
Top
 Profile  
 
stan thomison
 Post subject:
PostPosted: Mon Jan 17, 2005 9:12 am 
Offline
Contributing Member
Contributing Member

Joined: Mon Jan 03, 2005 7:46 am
Posts: 1315
Location: Branson, MO
First name: stan
Last Name: thomison
City: branson
State: mo
Zip/Postal Code: 65616
Country: united states
Focus: Build
Status: Professional
Thanks Steve. Been doing most at about .270 and less for thickness, thought was going a little short.
Top
 Profile  
 
Dickey
 Post subject:
PostPosted: Mon Jan 17, 2005 10:52 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Dec 29, 2004 5:10 am
Posts: 2020
Location: Argentina
I just cut a dozen sets of main xbraces, addy, 11/16ths tall is my blank size. 5/16ths wide, by 18 1/2 inches long, by 11/16ths tall. My Taylor Dred has 3/8 thick braces.
Top
 Profile  
 
John Kinnaird
 Post subject:
PostPosted: Mon Jan 17, 2005 11:06 am 
Offline
Koa
Koa

Joined: Sun Jan 09, 2005 1:50 am
Posts: 952
Location: United States
I typically make my braces about 1/4 inch wide and about 5/8 inch tall at the highest point. I also profile the braces to a tall triangular cross section and then make a porpois shaped curve to the brace that is thickest at the X and tapers out paper this at the perimeter. Braces are shaped so many different ways, that the absolute height of a brace is just a starting point. But, since I don't scallop near the bridge, thinner braces work well.
Top
 Profile  
 
Sprockett
 Post subject:
PostPosted: Mon Jan 17, 2005 11:56 am 
Offline
Koa
Koa

Joined: Wed Dec 29, 2004 3:25 am
Posts: 886
Location: United States
Mine are a hair bigger than 1/4" at the base (close to 9/32"), and about 3/4" at the tallest point (where the two braces cross), I then taper them from the soundboard up to a gradual point at the top (so the whole brace starts at a slight slope). I don't carve them in the martin fashion but taper them over towards the edges of the guitar and then put feet on then ends that notch into the top.

I also laminate in a CF strip to keep the top stable and add a little strength, makes carving a trick but I think the stability is worth the effort.

Cheers

-Paul-

_________________
-Paul-
Image
Patriot Guitars
Top
 Profile  
 
Sprockett
 Post subject:
PostPosted: Tue Jan 18, 2005 6:17 am 
Offline
Koa
Koa

Joined: Wed Dec 29, 2004 3:25 am
Posts: 886
Location: United States
Actually I have to correct my own statement (another sure sign that I'm getting older )..

That is for cedar braces, for spruces ones they are a bit under 1/4 and still about 3/4" tall....

-Paul-

_________________
-Paul-
Image
Patriot Guitars
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 

Board index » Forum Archive

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 63 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com