Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Tue Nov 26, 2024 1:39 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 21 posts ] 
Author Message
 Post subject: gluing cocobolo
PostPosted: Wed Mar 26, 2008 9:37 pm 
Offline
Cocobolo
Cocobolo

Joined: Sat Oct 27, 2007 1:49 pm
Posts: 144
Location: North Carolina
What solvent would you use to get the oil out of this wood to allow a good bond with LMI instrument glue. Last time I used epoxy and I hated it - what a pain!


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Wed Mar 26, 2008 10:02 pm 
Offline
Koa
Koa
User avatar

Joined: Wed Apr 18, 2007 6:46 am
Posts: 1012
Location: Issaquah, Washington USA
Steve, I'm not sure I'd bother with the solvent. I'm working on a cocobolo instrument right now. I cleaned the back plates with acetone before joining and I still had a partial joint failure - quickly fixed with CA. The rest of my gluing (using Titebond Original) has gone OK without using any solvent - just make sure the surfaces to be joined are fresh.

_________________
A higher purpose for wood.
Rich Smith
Issaquah, WA


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Wed Mar 26, 2008 10:12 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Wed Mar 19, 2008 10:48 pm
Posts: 344
Location: Tennessee
Someone told me to use naptha before gluing but I have done it yet so I can't really comment.

_________________
Jeremy Douglas


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Wed Mar 26, 2008 10:22 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sun Jun 24, 2007 1:14 am
Posts: 246
Location: United States
City: Keene
State: NH
If you're using coco for bindings, be sure to scrape them after bending. The oils like to come out of the wood and harden on the surface. just run a scraper over it.
- Justin


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 12:16 am 
Offline
Koa
Koa

Joined: Thu Dec 01, 2005 5:10 pm
Posts: 778
Location: Madison, WI
jmanter wrote:
If you're using coco for bindings, be sure to scrape them after bending. The oils like to come out of the wood and harden on the surface. just run a scraper over it.
- Justin

Ditto. I haven't found that the solvents are necessary. I just completed one with a cocobolo body and one with coco bindings. I used both fish glue and titebond on them after either sanding or scraping and had great success on both.

_________________
“If God dwells inside us like some people say, I sure hope He likes enchiladas, because that's what He's getting”
-jack handy


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 7:32 am 
Offline
Site Admin
User avatar

Joined: Mon Dec 27, 2004 5:02 am
Posts: 8551
Location: United States
First name: Lance
Last Name: Kragenbrink
City: Vandercook Lake
State: Michigan
Zip/Postal Code: 49203
Country: USA
Focus: Build
Status: Semi-pro
For some unknown reason, most of the guitars that I have made over the last three years have been with cocobolo
back and sides, not all but most.
I have used epoxy for all of them with 100% success rate, no joint failure (KNOCK ON WOOD).!! ;)

I don't wipe the joint either, just plane or sand (which ever you prefer) and glue up.

Why don't you like epoxy for (this) joint? Its so simple, and sands off in to a fine powder once cured.

One last comment, for rosewoods, I wont use anything but. IMHO its the most trustworthy.

_________________
Support the OLF! Bookmark our STEWMAC link Today!
Lance@LuthiersForum.com


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 7:45 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2004 1:20 pm
Posts: 5915
Location: United States
Epoxy for me too. I don't wipe the joints. Just joint it and glue.

_________________
Brock Poling
Columbus, Ohio
http://www.polingguitars.com


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 8:05 am 
Offline
Cocobolo
Cocobolo

Joined: Tue Jan 29, 2008 9:43 am
Posts: 310
Location: N.B. Canada
In regards to epoxy and oily woods, which brand of expoxy do you find is the most effective?
I'm binding my Koa build with Ziricote and noticed a large amount of oil baked on the outside surface when they came out of the bender. I plan on hitting them with acetone and a quick sand before installation.

Thanks,

Ray

_________________
Guitar Building = Continuous Improvement Process


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 8:33 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Aug 31, 2005 7:30 am
Posts: 1792
Location: United States
IME no solvent is necessary with oily woods. What compromises the bond are the oils coming to the surface and oxydizing, and/or a poorly fitted joint. A freshly planed/scraped/sanded surface will be fine with Titebond, epoxy, HHG etc. 2 parts hardware store epoxy works fine.

_________________
Laurent Brondel
West Paris, Maine - USA
http://www.laurentbrondel.com/


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 8:53 am 
Offline
Site Admin
User avatar

Joined: Mon Dec 27, 2004 5:02 am
Posts: 8551
Location: United States
First name: Lance
Last Name: Kragenbrink
City: Vandercook Lake
State: Michigan
Zip/Postal Code: 49203
Country: USA
Focus: Build
Status: Semi-pro
Laurent
On two different backs I had brace ends pop using LMI white glue.
It was from two different batches also because the guitars were at least 16 months or so apart.
Since that second "pop" I have used epoxy for my back braces on cocobolo/rosewoods as well. I think there is more to it than just a poorly fitted joint.
Not arguing, just telling of my experiences.

_________________
Support the OLF! Bookmark our STEWMAC link Today!
Lance@LuthiersForum.com


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 9:04 am 
Offline
Mahogany
Mahogany

Joined: Fri Apr 28, 2006 1:11 am
Posts: 52
Location: United States
I have used Smith's All Wood Epoxy without problem; I have used it to join backs and attach a fingerboard, all in cocobolo. I didn't find it difficult to use or particulary painful in any way. Even though you have the hassle of mixing it and it smells a bit, I wouldn't risk using other glues. Hoping that another glue will hold really isn't worth the risk. You don't want to work for months on your latest baby only to see it pop apart.


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 10:41 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue Jan 25, 2005 6:16 am
Posts: 2692
Lance Kragenbrink wrote:
Laurent
On two different backs I had brace ends pop using LMI white glue.
It was from two different batches also because the guitars were at least 16 months or so apart.
Since that second "pop" I have used epoxy for my back braces on cocobolo/rosewoods as well. I think there is more to it than just a poorly fitted joint.
Not arguing, just telling of my experiences.


I think it has been well established here (and at MIMF, as of a couple of years ago) that joint failures with hide glue are always caused by bad technique, while joint failures with any other glue are always caused by bad glue. :shock: [I know you're not arguing, Lance.].

Why not use epoxy, just to be safe? It's time consuming, expensive, and really messy; and aliphatic resin has not failed me. I used to wipe oily rosewoods like cocobolo with acetone and use either aliphatic resin or hide glue with no problems. Now I make sure I have a fresh surface and don't wipe, mostly using Aliphatic resin, also with no problems.

Squeeze out can't weaken a glue joint, but not putting enough glue in the joint sure can.

_________________
Howard Klepper
http://www.klepperguitars.com

When all else fails, clean the shop.


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 11:41 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Aug 31, 2005 7:30 am
Posts: 1792
Location: United States
Lance, that bites…
I've not had problems with cocobolo so far, gluing spruce and mahogany back braces. I use Titebond and have not yet used LMI white.
I've not had issues either with gluing cocobolo bridges on spruce, and even redwood. I don't lather the glue, just spread it out evenly (that's the role of the pinky) and make sure I have enough squeeze out.

_________________
Laurent Brondel
West Paris, Maine - USA
http://www.laurentbrondel.com/


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 11:41 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue Jan 25, 2005 6:16 am
Posts: 2692
Oh, the squeeze out thing was on another thread, sorry.

_________________
Howard Klepper
http://www.klepperguitars.com

When all else fails, clean the shop.


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 12:03 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jan 22, 2008 8:32 pm
Posts: 64
Location: Canada
Ive used Smiths All Wood Epoxy on the neck and tail blocks, Titebond on the linings and fish glue on the back braces. I didnt use any solvents on the cocobolo, just sanded or scraped. The instructions from Smiths said not to use any solvents as that would weaken the joint. Everythings holding together so far. Course its not completed yet....
Warren


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 12:20 pm 
Offline
Site Admin
User avatar

Joined: Mon Dec 27, 2004 5:02 am
Posts: 8551
Location: United States
First name: Lance
Last Name: Kragenbrink
City: Vandercook Lake
State: Michigan
Zip/Postal Code: 49203
Country: USA
Focus: Build
Status: Semi-pro
Luckily it was before the back was glued on, so very easy to fix. But it does make me gun shy.
The Epoxy just seems so easy, especially for the center seam. For back brace squeeze out, I use a damp rag with some DA on it and the epoxy wipes right off clean. TO MUCH DA will make COCO bleed like a stuck pig though wow7-eyes

_________________
Support the OLF! Bookmark our STEWMAC link Today!
Lance@LuthiersForum.com


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 12:25 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Tue Jan 25, 2005 6:16 am
Posts: 2692
Looking at it sideways will make coco bleed. Seems that if there is a light colored wood adjacent to it, you can always see a little bleed when finish is applied.

_________________
Howard Klepper
http://www.klepperguitars.com

When all else fails, clean the shop.


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 8:50 pm 
Offline
Cocobolo
Cocobolo

Joined: Sat Oct 27, 2007 1:49 pm
Posts: 144
Location: North Carolina
Thanks for all the comments and suggestions. The reason I don't like the epoxy is because I like to use a vacuum press for back bracing and the slow set just takes too long. The LMI All Wood Epoxy takes hours to set.

Steve


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 9:19 pm 
Offline
Koa
Koa

Joined: Thu Jul 07, 2005 1:15 am
Posts: 575
Location: United States
I agree with Howard here (Hello, Howard!), and others too who have said that all you need to do is have a fresh surface, regular titebond and hide glue which both work fine for me.
I have heard of some failures with the LMI white glue.

_________________
Mark Swanson
Swanson Guitars

http://www.MarkSwansonMusic.com
Image


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 9:20 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Oct 21, 2006 7:07 am
Posts: 280
Location: United States
I have a friend who is an anthropological linguist, specializing in archaic mesoamerican languages. I don't know how it came up, but we started talking wood, and he pointed out the similiarity between an ancient Mayan phrase, "coc'ke' abola" which can be loosely translated as " may as well try to glue wax paper".

I found that interesting.

_________________
It's not the miles ahead, it's the stone in your shoe


In Markham,Virginia


Top
 Profile  
 
 Post subject: Re: gluing cocobolo
PostPosted: Thu Mar 27, 2008 9:22 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Oct 21, 2006 7:07 am
Posts: 280
Location: United States
laughing6-hehe

_________________
It's not the miles ahead, it's the stone in your shoe


In Markham,Virginia


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 21 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 53 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com