Official Luthiers Forum! • View topic

Board index » Forum Archive

All times are UTC - 5 hours

Drilling end pins

Page 1 of 1

[ 8 posts ]

Print view

Previous topic | Next topic

Author

Message

Andy Zimmerman

Post subject:

Posted: Sat Oct 15, 2005 5:58 am

Brazilian Rosewood

Joined: Fri Jun 10, 2005 9:51 am
Posts: 2148
Location: San Diego, CA
First name: Andy
Last Name: Zimmerman
City: San Diego
State: CA
Zip/Postal Code: 92103
Country: United States
Focus: Build

If you have a guitar that you are going to drill a 1/2" hole for a endpin jack
and there is no hole already. Do you?
A) Drill a 1/2" hole with a brad point
or
B) Drill a small pilot hole and then use a step drill to enlarge the hole

Thanks
Andy

_________________
Andy Z.
http://www.lazydogguitars.com

Top

RussellR

Post subject:

Posted: Sat Oct 15, 2005 6:10 am

Brazilian Rosewood

Joined: Thu Jun 16, 2005 10:31 am
Posts: 2103
Location: United Kingdom

Andy

I would use the step drill. Also tape the end graft over with masking tape to avoid chipping.

For mine I use a pilot hole and a reamer.

Top

Brock Poling

Post subject:

Posted: Sat Oct 15, 2005 8:24 am

Old Growth Brazilian Rosewood

Joined: Mon Dec 27, 2004 1:20 pm
Posts: 5915
Location: United States

Drill a hole and use a hand reamer to get it to the final size.

_________________
Brock Poling
Columbus, Ohio
http://www.polingguitars.com

Top

Don Williams

Post subject:

Posted: Sat Oct 15, 2005 8:41 am

Contributing Member

Joined: Mon Dec 27, 2004 11:25 pm
Posts: 7207
Location: United States

What Brock said.

_________________
"I want to know what kind of pickups Vince Gill uses in his Tele, because if I had those, as good of a player as I am, I'm sure I could make it sound like that.
Only badly."

Top

Dave Rector

Post subject:

Posted: Sat Oct 15, 2005 9:51 am

Brazilian Rosewood

Joined: Sat Feb 12, 2005 1:07 am
Posts: 2281
Location: Jones, OK

What Don said.

_________________
Dave Rector
Rector Guitars

Top

Andy Zimmerman

Post subject:

Posted: Sat Oct 15, 2005 11:09 am

Brazilian Rosewood

Where do you get a good hand reamer that gets to 1/2"
Thanks
Andy

_________________
Andy Z.
http://www.lazydogguitars.com

Top

Brock Poling

Post subject:

Posted: Sat Oct 15, 2005 11:28 am

Old Growth Brazilian Rosewood

Joined: Mon Dec 27, 2004 1:20 pm
Posts: 5915
Location: United States

Grizzly has them among other places.

_________________
Brock Poling
Columbus, Ohio
http://www.polingguitars.com

Top

HankMauel

Post subject:

Posted: Sat Oct 15, 2005 12:20 pm

Cocobolo

Joined: Wed Jan 05, 2005 4:23 am
Posts: 267
Location: United States

Get a piloted reamer...and check the diameters; you may find that most end jacks are really 15/32" diameter. See the discussion on drilling tuner holes eslewhere in the Forum.
Replace the "pilot" with the equivalent drill diameter, tape off the area as mentioned, find the center point and punch a small starting dimple with an awl, then drill and ream in one action. Do go slow with any drill on a finished instrument, no matter what method you choose.

Top

Page 1 of 1

[ 8 posts ]

Board index » Forum Archive

All times are UTC - 5 hours

Who is online

Users browsing this forum: No registered users and 9 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: