Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Dec 12, 2024 9:54 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 41 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Soundhole reinforcement
PostPosted: Sun Oct 22, 2017 7:15 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
So here’s an idea that is, I’m SURE, more complicated than it is worth.

I’ve seen some folks reinforce the soundhole area with a solid ring on the inside. Some do the traditional thin “braces” on 3 sides and I’ve even seen some attach binding to the inside of the ring to seal off the end grain.

So I wonder... has anyone done like an “insert”?
What I mean is a round reinforcement that will be under the soundhole, but also has a raised lip that inserts into the sound hole and comes flush with the top.

I’ll include a REAL bad drawing to farther complicate things here :)

Check out this art!
Image


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Sun Oct 22, 2017 7:20 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jan 26, 2016 10:59 pm
Posts: 54
First name: Jonny
Last Name: Fifield
Country: Canada
Focus: Build
Status: Amateur
You mean a 4" sound hole flange ?

_________________
"Practice enough till the results aren't hopes but expectations" forum member Peter Havriluk



These users thanked the author Jonny for the post: Bryan Bear (Sun Oct 22, 2017 8:13 pm)
Top
 Profile  
 
PostPosted: Sun Oct 22, 2017 7:43 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sun Mar 30, 2008 8:20 am
Posts: 5968
I think Ovation did something similar, only in plastic, and on the outside of the guitar (plastic rosette).

You would probably be better off doing the "doughnut" reinforcement and then binding the sound hole. That way there is no end grain exposed.


Top
 Profile  
 
PostPosted: Sun Oct 22, 2017 8:05 pm 
Offline
Koa
Koa

Joined: Sun Apr 25, 2010 4:46 pm
Posts: 527
First name: Mark
Last Name: McLean
City: Sydney
State: New South Wales
Zip/Postal Code: 2145
Country: Australia
Focus: Build
Status: Amateur
I agree with what Clay just said. It is a good idea to have soundhole reinforcement. It can also look really nice to have a soundhole binding, say in the same timber as your other bindings. You could achieve both things with one piece of timber, as you have suggested. However, I think it could be a real hassle to engineer that with a perfect fit. I usually do the donut in off-cuts of the soundboard (softwood, light). Then you will have a thickness of about 5-6mm at the cut edge of the soundhole and it is pretty easy to bend a piece of your binding into a circle and fit that to cover the end grain. It has the advantage of usually being a hardwood, for better protection of the edge of the hole. If you can do that with one piece I will be really impressed, so take some photos to show us.......


Top
 Profile  
 
PostPosted: Sun Oct 22, 2017 8:29 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
Mark Mc wrote:
I agree with what Clay just said. It is a good idea to have soundhole reinforcement. It can also look really nice to have a soundhole binding, say in the same timber as your other bindings. You could achieve both things with one piece of timber, as you have suggested. However, I think it could be a real hassle to engineer that with a perfect fit. I usually do the donut in off-cuts of the soundboard (softwood, light). Then you will have a thickness of about 5-6mm at the cut edge of the soundhole and it is pretty easy to bend a piece of your binding into a circle and fit that to cover the end grain. It has the advantage of usually being a hardwood, for better protection of the edge of the hole. If you can do that with one piece I will be really impressed, so take some photos to show us.......

Even if I could i would still have end grain exposed:/ I do like the binding idea, but haven’t tried it.
I suppose all I really need is a 4” hot pipe to bend around


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Sun Oct 22, 2017 9:16 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7385
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
SnowManSnow wrote:
Mark Mc wrote:
I agree with what Clay just said. It is a good idea to have soundhole reinforcement. It can also look really nice to have a soundhole binding, say in the same timber as your other bindings. You could achieve both things with one piece of timber, as you have suggested. However, I think it could be a real hassle to engineer that with a perfect fit. I usually do the donut in off-cuts of the soundboard (softwood, light). Then you will have a thickness of about 5-6mm at the cut edge of the soundhole and it is pretty easy to bend a piece of your binding into a circle and fit that to cover the end grain. It has the advantage of usually being a hardwood, for better protection of the edge of the hole. If you can do that with one piece I will be really impressed, so take some photos to show us.......

Even if I could i would still have end grain exposed:/ I do like the binding idea, but haven’t tried it.
I suppose all I really need is a 4” hot pipe to bend around


Sent from my iPhone using Tapatalk Pro
Just use the regular bending iron. I've done several. The hardest part is to bend the binding without breaking it.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Sun Oct 22, 2017 9:24 pm 
Offline
Koa
Koa

Joined: Sun Apr 25, 2010 4:46 pm
Posts: 527
First name: Mark
Last Name: McLean
City: Sydney
State: New South Wales
Zip/Postal Code: 2145
Country: Australia
Focus: Build
Status: Amateur
It is a fairly tight bend, but no worst than many cutaways. Thin the binding strip down a bit. Super-soft can help. Use a metal backing slat. But it is no different from hand bending a normal binding. I do them on a normal bending iron - no need for a special tool for this job.

I think I remember seeing a YouTube video by Nigel Forster, which you could search for. He made it look easy so I tried it, and I only snapped 2 or 3 before I got it right (so maybe don't do it with your valuable BRW bindings for the first attempt).
Here is the video from Nigel:
https://www.youtube.com/watch?v=9f_t-wGo30o&sns=em


Top
 Profile  
 
PostPosted: Mon Oct 23, 2017 12:13 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
Are you envisioning the insert being made from a single piece of wood? What wood would the insert be made of?

It wouldn't be hard to make an insert like that that fits nicely from one piece of wood using a router in a circle cutter base. If it was made from spruce though, I think it might look a bit odd to have a narrow ring of spruce around the soundhole opening with a different grain than the surrounding top wood.

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter


Top
 Profile  
 
PostPosted: Mon Oct 23, 2017 4:31 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 13417
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
Back in the day the G*bson MK series was state of the art with unique bracing and the design resulted from a collaboration between Kasha and Richard Schneider. They had a genuine, imitation pl*stic.... sound hole..... thing..... that I believe was supposed to project like a trumpet.

Like many things in the guitar world it didn't work as envisioned, the guitars are widely considered to be pieces of crap.... and although they have their following it's just one more example of why attempting to reinvent the wheel before understanding more completely traditional guitar design tends to be a rather futile pursuit. Resistance is futile.....;). There are very good reasons why sound holes look like they do these days.

Don't mean to be a buzz kill but there is very little that has not been done prior in the guitar world.

Image

We have a collector who is a client and we work on several of the MKs from time to time. One of his still has vomit chunks and bong water stains from when he went to Michigan State University. Provenance..... they say.... :? :roll: [xx(] :D The only thing I hate worse than a guitar with vomit in the sound hole is a Rikinbacker 12 string. I just doubled my pricing to set up the Rik 12's because they make me want to puke every time I have to work on them. What were they thinking....;)


Top
 Profile  
 
PostPosted: Mon Oct 23, 2017 4:11 pm 
Offline
Contributing Member
Contributing Member

Joined: Tue Mar 04, 2008 11:55 am
Posts: 566
First name: Bob
Last Name: Shanklin
City: Windsor
State: ON
Country: Canada
If you decide to bind the sound hole, make yourself a Soundhole Binding Clamp from a piece of 3.5" plastic drain pipe and a few wedges. The clamp will hold the binding tight in the sound hole.


download/file.php?mode=view&id=57491&sid=f5f8ec0aa4c028243737da4137e0a2d3http://www.luthiersforum.com/forum/download/file.php?mode=view&id=57492

Bob


You do not have the required permissions to view the files attached to this post.



These users thanked the author Bob Shanklin for the post (total 11): jfmckenna (Wed Dec 29, 2021 11:28 am) • TimAllen (Tue Sep 28, 2021 11:58 am) • kwerry (Wed Nov 22, 2017 2:05 pm) • Jonny (Wed Oct 25, 2017 3:39 pm) • GRS (Tue Oct 24, 2017 8:12 am) • Ken Franklin (Tue Oct 24, 2017 1:45 am) • Pmaj7 (Mon Oct 23, 2017 7:25 pm) • Clay S. (Mon Oct 23, 2017 5:14 pm) • Alex Kleon (Mon Oct 23, 2017 5:10 pm) • Bryan Bear (Mon Oct 23, 2017 4:38 pm) and one more user
Top
 Profile  
 
PostPosted: Mon Oct 23, 2017 5:08 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
Another approach for binding the sound hole is to treat it as another ring of inlay. I bend a ring and then rout an appropriately sized channel into the top and inlay the ring. The depth of the channel is a few thousandths shy of going through the top. Later, I rout out the sound hole opening inside the binding ring. In the photo below, the innermost ring is cocobolo sound hole binding.

Attachment:
Rosette inlay 3.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post (total 6): giltzow (Wed Nov 22, 2017 5:53 pm) • johnparchem (Wed Nov 22, 2017 1:36 pm) • Jonny (Wed Nov 22, 2017 12:41 pm) • bftobin (Mon Oct 23, 2017 8:45 pm) • Bryan Bear (Mon Oct 23, 2017 5:44 pm) • Clay S. (Mon Oct 23, 2017 5:14 pm)
Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 8:20 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Apr 08, 2009 9:34 am
Posts: 3081
Yup, that's the way Larson's did it in the '30's...
When I did it, the inside ivoroid ring exposed approx 1/2 the thickness of the top. Some folks need to see that QS grain.
Never cared for the idea of anything sticking above the sound hole (difficult to finish), but was a firm believer in sound hole re-inforcement. I used a spruce doubler that ran full span from X to UTB or on Ladder bracing, UTB to LTB. In addition, I also used the 3 braces around the sound hole, or 2 on ladders.
Someone a long time ago demonstrated to me that lightly braced sound holes distort and can cause dissonance.


Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 5:56 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Mar 26, 2013 6:49 pm
Posts: 403
First name: Fred
City: Winnipeg
Country: Canada
Focus: Build
Status: Amateur
I like the ABS pipe idea. I did add a few more clamps yet but I took a picture during the process of clamping.

Image

Oh wait, this was my doing a dry run.


Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 6:35 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Sat Feb 02, 2008 9:19 am
Posts: 184
Focus: Build
Status: Amateur
I really like that idea Jay. It would make the clamping and gluing soooo much,easier to handle and since I leave the tops a little thick when installing the rosette.


Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 6:56 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2524
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington
I nominate Fred for this month's Award for Creative Excellence in Clamping Accessories! [:Y:]

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter



These users thanked the author J De Rocher for the post: printer2 (Tue Oct 24, 2017 7:09 pm)
Top
 Profile  
 
PostPosted: Tue Oct 24, 2017 7:16 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Mar 26, 2013 6:49 pm
Posts: 403
First name: Fred
City: Winnipeg
Country: Canada
Focus: Build
Status: Amateur
J De Rocher wrote:
I nominate Fred for this month's Award for Creative Excellence in Clamping Accessories! [:Y:]


I didn't want any marks on the sides, I already scraped them smooth. I think I will get another lid for the other bout, when actually gluing and clamping the soundhole trim I had the inner tube go around the whole exterior of the guitar. When taking off the clamps no marks. Got to love Mother when necessity calls. Or something like that.


Top
 Profile  
 
PostPosted: Wed Oct 25, 2017 12:58 am 
Offline
Koa
Koa
User avatar

Joined: Thu Aug 25, 2005 4:49 pm
Posts: 1209
Location: Ukiah, CA
Here is a jig made by Link Van Cleave that makes the binding more uniformly round. I can get it close on the pipe and then heat it up on a hot plate. I like to do a scarf joint at the ends.

Attachment:
IMG_1058.jpg


Attachment:
IMG_1059.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Ken Franklin
clumsy yet persistent
https://www.kenfranklinukulele.com



These users thanked the author Ken Franklin for the post: Jonny (Wed Oct 25, 2017 3:40 pm)
Top
 Profile  
 
PostPosted: Wed Oct 25, 2017 2:31 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Feb 17, 2013 4:58 pm
Posts: 1449
First name: Ed
Last Name: Minch
City: Chestertown
State: MD
Zip/Postal Code: 21620
Country: United States
Focus: Build
Status: Amateur
Just did some cuffs on the legs of a dressing table - the legs were 1-3/8" and the cuffs were .075" spruce. I boiled them for 15 minutes and wrapped them around an appropriate sized dowel and let them dry. Worked well with careful stock selection.

https://www.flickr.com/photos/ruby1638/35176717312/in/album-72157680433239633/

I love the idea of the hose clamp around the form. I have glued the soundhole binding into an extra rosette groove before final sanding, and made it almost full depth, glue on one side only. When I sanded the top, the middle plug just fell out. Not my idea.

I also love the interior split pipe clamp - next time.

Ed


Top
 Profile  
 
PostPosted: Wed Oct 25, 2017 7:41 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Apr 08, 2009 9:34 am
Posts: 3081
Test!

Here's an old 12 string ladder with sound hole doubler...

Image

Looks like I will be able to post photos again...I hope.


Top
 Profile  
 
PostPosted: Wed Nov 22, 2017 9:43 am 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
I wanted to revisit this.
So, I’m nervous about gluing a “binding strip” to the inside of the hole for some reason... I guess I don’t trust my luthier powers yet... and I’d hate for it to pop off if hit by a pick or something.
What about making what is basically an inner rosette that covered the area where the sound hole will be cut before thicknessing from the back and then cutting the hole from that? Would this leave a weak area?
I guess, if I want this to be part of my arsenal in the future I just need to cut some practice sound holes and do it right until I get it right.
Well, thanks for the conversation. Haha


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Wed Nov 22, 2017 9:49 am 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
J De Rocher wrote:
Another approach for binding the sound hole is to treat it as another ring of inlay. I bend a ring and then rout an appropriately sized channel into the top and inlay the ring. The depth of the channel is a few thousandths shy of going through the top. Later, I rout out the sound hole opening inside the binding ring. In the photo below, the innermost ring is cocobolo sound hole binding.

Attachment:
Rosette inlay 3.jpg

Yup. Like this
Already addressed
Sorry for raising the dead


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Wed Nov 22, 2017 11:31 am 
Offline
Contributing Member
Contributing Member

Joined: Fri Jun 04, 2010 10:02 pm
Posts: 313
First name: Michael
Last Name: Giltzow
City: Boise
State: Idaho
Zip/Postal Code: 83709
Country: usa
Focus: Build
Status: Semi-pro
Hey SnowManSnow

If I understand your drawing correctly: I do some of my sound holes like that. Not a binding but an inlay. Pics below:

Image

Image

- Mike G

_________________
guitarsbygiltzow.com


Top
 Profile  
 
PostPosted: Wed Nov 22, 2017 11:47 am 
Offline
Contributing Member
Contributing Member

Joined: Fri Jun 04, 2010 10:02 pm
Posts: 313
First name: Michael
Last Name: Giltzow
City: Boise
State: Idaho
Zip/Postal Code: 83709
Country: usa
Focus: Build
Status: Semi-pro
Here's another pic with more detail:

Image

_________________
guitarsbygiltzow.com



These users thanked the author giltzow for the post: J De Rocher (Wed Nov 22, 2017 1:19 pm)
Top
 Profile  
 
PostPosted: Wed Nov 22, 2017 12:53 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1707
Yea that’s what the original idea was
It doesn’t seal the end grain but does look nice;)


Sent from my iPhone using Tapatalk Pro


Top
 Profile  
 
PostPosted: Wed Nov 22, 2017 1:43 pm 
Offline
Mahogany
Mahogany

Joined: Mon Sep 17, 2007 12:00 pm
Posts: 60
Location: Australia
Besides appearance, don't forget the structural aspects of soundhole reinforcement and bracing.
Cutting the channel for the rosette leaves the soundboard quite thin in this area, and compressive forces from the string tension have to pass through a fairly narrow strip of soundboard outside the soundhole.
I just had to do some extensive repair on a CSL macafferi big mouth, which had warped like a potato chip both sides of the soundhole. The plastic rosette had popped out of it's groove too
No reinforcement, no bracing, what were they thinking?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 41 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: Craig Wilson, Gary Davis and 26 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com