Official Luthiers Forum! • View topic - Well, that wasn't a good start to the day

Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours

Forum rules

Be nice, no cussin and enjoy!

Well, that wasn't a good start to the day - drum sander

Page 2 of 2

[ 30 posts ]

Go to page Previous 1, 2

Print view

Previous topic | Next topic

Author

Message

meddlingfool

Post subject: Re: Well, that wasn't a good start to the day - drum sander

Posted: Mon Feb 08, 2021 10:44 pm

Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7380
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional

Sweet Victory!

These users thanked the author meddlingfool for the post: J De Rocher (Tue Feb 09, 2021 1:34 am)

Top

wbergman

Post subject: Re: Well, that wasn't a good start to the day - drum sander

Posted: Tue Feb 09, 2021 8:54 am

Koa

Joined: Mon Dec 18, 2006 9:42 am
Posts: 1577
Location: United States

Not sure if this was already discussed. The tightness of the nuts holding the slide plates might matter a lot, but I do not know how loose is safe.

Top

John Arnold

Post subject: Re: Well, that wasn't a good start to the day - drum sander

Posted: Tue Feb 09, 2021 12:30 pm

Contributing Member

Joined: Wed Sep 08, 2010 12:17 am
Posts: 1286
First name: John
Last Name: Arnold
City: Newport
State: TN
Zip/Postal Code: 37821
Country: USA
Focus: Repair
Status: Professional

If the gibs are loose enough to detect play when pushing on the end of the drum carrier, they are too loose. This would make it nearly impossible to adjust the sander for uniform thickness across the width of the drum. It could also encourage vibration, which will cause ripples in the wood.

_________________
John

These users thanked the author John Arnold for the post: wbergman (Tue Feb 09, 2021 4:16 pm)

Top

J De Rocher

Post subject: Re: Well, that wasn't a good start to the day - drum sander

Posted: Tue Feb 09, 2021 1:05 pm

Contributing Member

Joined: Mon Apr 16, 2012 12:47 pm
Posts: 2523
First name: Jay
Last Name: De Rocher
City: Bothell
State: Washington

The owner's manual says to fully tighten the Gib bolts and then back them off 1/8 to 1/4 turn. You then tighten a lock nut on each Gib bolt to keep them where you set them. I backed mine off 1/8 turn and the mechanism slides smoothly.

_________________
Once in a while you get shown the light in the strangest of places if you look at it right - Robert Hunter

These users thanked the author J De Rocher for the post: wbergman (Tue Feb 09, 2021 4:16 pm)

Top

doncaparker

Post subject: Re: Well, that wasn't a good start to the day - drum sander

Posted: Tue Feb 09, 2021 1:16 pm

Contributing Member

Joined: Tue Dec 17, 2013 10:52 pm
Posts: 3072
First name: Don
Last Name: Parker
City: Charleston
State: West Virginia
Zip/Postal Code: 25314
Country: USA
Focus: Build
Status: Amateur

Glad it worked out in the end! The rest of the good news is that, notwithstanding this problem, the other parts of a pre-Jet Performax sander are pretty solid. I have one of the closed frame pre-Jet versions (ShopPro 25), and it is built to last.

Top

Page 2 of 2

[ 30 posts ]

Go to page Previous 1, 2

Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours

Who is online

Users browsing this forum: Bing [Bot] and 40 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: